HP LH4r HP Netserver LPr Installation Guide - Page 59

Installing Additional, Processors

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Chapter 8 Installing Additional Processors Introduction The NetServer LPr supports up to two processor modules. Processor modules are available at different clock speeds. Both processor modules must operate at the same clock frequency. The processor upgrade kit includes the HP NetServer Navigator CD-ROM. Boot with this CD-ROM after installing the additional processor to update the BIOS. Tools Required These tools are required for removal and installation of CPU modules: • If you have to remove the LPr chassis from the rack, use Torx T25 driver. Refer to the last section of Chapter 9, "Removing the NetServer from the Rack" for instructions. • An anti-static service kit (3M™ 8501/8502/8503 or equivalent). This kit includes a static-dissipating work surface, a chassis clip lead, and a wrist strap. Installation Steps Verify Contents CAUTION Do not remove the processor from its bag until you are ready to install it. Make sure the bag remains sealed. The CPU chips are sensitive to humidity, so desiccant has been packed in the bag containing the processor board. When the processor board has been installed and the HP NetServer is running, the chips are no longer sensitive to humidity. Unpack the shipping box and verify that you received the contents in the following list for the processor accessory kit. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
51
Chapter 8
Installing Additional
Processors
Introduction
The NetServer LPr supports up to two processor modules. Processor modules are
available at different clock speeds. Both processor modules must operate at the
same clock frequency.
The processor upgrade kit includes the
HP NetServer Navigator CD-ROM
. Boot
with this CD-ROM after installing the additional processor to update the BIOS.
Tools Required
These tools are required for removal and installation of CPU modules:
•
If you have to remove the LPr chassis from the rack, use Torx T25 driver.
Refer to the last section of Chapter 9, "Removing the NetServer from the
Rack" for instructions.
•
An anti-static service kit (3M
8501/8502/8503 or equivalent). This kit
includes a static-dissipating work surface, a chassis clip lead, and a wrist
strap.
Installation Steps
Verify Contents
CAUTION
Do not remove the processor from its bag until you are ready
to install it. Make sure the bag remains sealed. The CPU
chips are sensitive to humidity, so desiccant has been packed
in the bag containing the processor board. When the
processor board has been installed and the HP NetServer is
running, the chips are no longer sensitive to humidity.
Unpack the shipping box and verify that you received the contents in the
following list for the processor accessory kit.