HP LH4r HP Netserver LPr Installation Guide - Page 91

Custom Configuration

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Chapter 11 Configuring the NetServer LPr select Configure Remote Management on the Configure Remote Management screen. • Show System Information: Use this screen to display information about standard and accessory boards and devices in the system, as well as the used and available system resources. ◊ Select View Hardware Inventory on the Show System Information screen to display information about standard and accessory boards and devices in the system. ◊ Select View Resources on the Show System Information screen to display used and available system resources such as memory ranges, I/O port ranges, DMA channels, and interrupt (IRQ) levels. • Configure Disk Array. Configures your HP disk array. Before preceding, fill out the Disk Array Configuration Worksheet. Click Help for more details. • Install Utility Partition: This step creates a utility partition on the server hard disk where HP Navigator will copy DiagTool, the BIOS Update utility, the Event Log Report utility, the Disk Array utility, the NIC Configuration utility, the Integrated Remote Assistant utilities, troubleshooting utilities, and other utilities. It is not available for SCO UNIX. Select Execute on the Install Utility Partition screen. • Execute Card Utilities: When Configuration Assistant detects installed boards for which there are additional configuration utilities on the HP NetServer Navigator CD-ROM, you can execute these utilities to complete the configuration of the boards by selecting Execute on the Execute Board Utilities screen. Custom Configuration In Custom configuration mode, you perform the same configuration steps as for Express configuration mode, but you can do them in any order. Select Custom on the Configuration Assistant menu if you are experienced in NetServer configuration and have a preferred sequence of steps, or if you prefer to configure your system one component at a time. After you have selected the NOS, version, and NOS installation mode (automated or manual), and after you have viewed the Configuration Advisories, the Custom Configuration screen displays the following menu: 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Chapter 11
Configuring the NetServer LPr
83
select
Configure Remote Management
on the Configure Remote
Management screen.
•
Show System Information: Use this screen to display information about
standard and accessory boards and devices in the system, as well as the
used and available system resources.
◊
Select
View Hardware Inventory
on the Show System Information
screen to display information about standard and accessory boards and
devices in the system.
◊
Select
View Resources
on the Show System Information screen to
display used and available system resources such as memory ranges,
I/O port ranges, DMA channels, and interrupt (IRQ) levels.
•
Configure Disk Array. Configures your HP disk array. Before preceding,
fill out the Disk Array Configuration Worksheet. Click
Help
for more
details.
•
Install Utility Partition: This step creates a utility partition on the server
hard disk where HP Navigator will copy DiagTool, the BIOS Update
utility, the Event Log Report utility, the Disk Array utility, the NIC
Configuration utility, the Integrated Remote Assistant utilities,
troubleshooting utilities, and other utilities. It is not available for SCO
UNIX. Select
Execute
on the Install Utility Partition screen.
•
Execute Card Utilities: When Configuration Assistant detects installed
boards for which there are additional configuration utilities on the
HP
NetServer Navigator CD-ROM
, you can execute these utilities to complete
the configuration of the boards by selecting
Execute
on the Execute Board
Utilities screen.
Custom Configuration
In Custom configuration mode, you perform the same configuration steps as for
Express configuration mode, but you can do them in any order. Select
Custom
on
the Configuration Assistant menu if you are experienced in NetServer
configuration and have a preferred sequence of steps, or if you prefer to configure
your system one component at a time.
After you have selected the NOS, version, and NOS installation mode (automated
or manual), and after you have viewed the Configuration Advisories, the Custom
Configuration screen displays the following menu: