HP LH4r HP Netserver LPr Installation Guide - Page 109

Clearing the System Configuration

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 109 highlights

Chapter 13 Troubleshooting ◊ If you have changed any switches on the system board, check that they are properly set. 5. Reseat the system board in the card edge connector to the I/O board. 6. Turn on the display and HP NetServer LPr. 7. If the HP NetServer LPr still does not work: ◊ Repeat steps 1, 2, and 3 of this section. ◊ Remove all accessories, except the primary boot hard disk drive. ◊ Replace the cover and connect all cables. ◊ Turn on the display and the HP NetServer LPr. ◊ If the HP NetServer now works, replace the boards and accessories one at a time to determine which one is causing the problem. Clearing the System Configuration You may need to clear the system configuration if the configuration has been corrupted by a program, or if incorrect settings made in the Setup utility have made the display unreadable. To clear the system configuration, follow the steps on the next pages. 101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Chapter 13
Troubleshooting
101
◊
If you have changed any switches on the system board, check that they
are properly set.
5.
Reseat the system board in the card edge connector to the I/O board.
6.
Turn on the display and HP NetServer LPr.
7.
If the HP NetServer LPr still does not work:
◊
Repeat steps 1, 2, and 3 of this section.
◊
Remove all accessories, except the primary boot hard disk drive.
◊
Replace the cover and connect all cables.
◊
Turn on the display and the HP NetServer LPr.
◊
If the HP NetServer now works, replace the boards and accessories one
at a time to determine which one is causing the problem.
Clearing the System Configuration
You may need to clear the system configuration if the configuration has been
corrupted by a program, or if incorrect settings made in the Setup utility have
made the display unreadable.
To clear the system configuration, follow the steps on the next pages.