HP LH4r HP Netserver LPr Installation Guide - Page 37

the ejector handle engages the drive with the electrical connector in

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Chapter 4 Installing Mass Storage Devices Installing Hot-Swap Drives 3. Slide the drive slowly into the hot swap bay until it stops. See Figure 4-4. CAUTION Be careful not to damage the light pipes as you insert the drive. They are very fragile. You must insert the drive slowly and gently . If the drive is inserted too quickly when the system is on, in-rush current can cause the power supply to shut down. 4. Press the ejector handle in until you feel the latch click into place. Closing the ejector handle engages the drive with the electrical connector in the hot-swap mass storage cage and seats the drive. 5. If the drive is unseated in the cage after closing the ejector handle, the handle was probably not pulled out far enough, and the locking latch failed to engage the hot-swap mass storage cage. Repeat from step 2. Figure 4-4. Installing a Drive in the HP NetServer LPr 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Chapter 4
Installing Mass Storage Devices
29
Installing Hot-Swap Drives
3.
Slide the drive slowly into the hot swap bay until it stops. See Figure 4-4.
CAUTION
Be careful not to damage the light pipes as you insert the
drive. They are very fragile.
You must insert the drive slowly and gently
. If the drive is
inserted too quickly when the system is on, in-rush current
can cause the power supply to shut down.
4.
Press the ejector handle in until you feel the latch click into place. Closing
the ejector handle engages the drive with the electrical connector in the
hot-swap mass storage cage and seats the drive.
5.
If the drive is unseated in the cage after closing the ejector handle, the
handle was probably not pulled out far enough, and the locking latch
failed to engage the hot-swap mass storage cage. Repeat from step 2.
Figure 4-4. Installing a Drive in the HP NetServer LPr