HP LH4r HP Netserver LPr Installation Guide - Page 53

the top. The tabs at the bottom should capture the AC power

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Chapter 7 Installing Additional Boards 11. Position the PCI card, component side up, and slide it into the slo t. CAUTION Do not bend the PCI card to fit it into the slot. Check to make sure you removed any handles or board extenders as shown in Figure 7-1. Figure 7-5. Inserting a PCI Card 12. Use the T15 driver to screw the PCI card rear panel to the I/O panel at the rear of the LPr chassis. Refer to Figure 7-5. 13. Position the PCI retaining bracket and screw it down with the T15 driver. 14. Align the PCI access cover and snap it into place. NOTE The PCI access cover hinges at the bottom and swings in at the top. The tabs at the bottom should capture the AC power line on the enclosure floor and hold it against the enclosure side. Once the PCI card is installed, simply reboot the system. The drivers for the new card are either part of your existing system software, or you will load drivers from a floppy diskette that accompanies your upgrade card. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Chapter 7
Installing Additional Boards
45
11.
Position the PCI card, component side up, and slide it into the slo t.
CAUTION
Do not bend the PCI card to fit it into the slot. Check to make
sure you removed any handles or board extenders as shown in
Figure 7-1.
Figure 7-5. Inserting a PCI Card
12.
Use the T15 driver to screw the PCI card rear panel to the I/O panel at the
rear of the LPr chassis. Refer to Figure 7-5.
13.
Position the PCI retaining bracket and screw it down with the T15 driver.
14.
Align the PCI access cover and snap it into place.
NOTE
The PCI access cover hinges at the bottom and swings in at
the top. The tabs at the bottom should capture the AC power
line on the enclosure floor and hold it against the enclosure
side.
Once the PCI card is installed, simply reboot the system. The drivers for the new
card are either part of your existing system software, or you will load drivers
from a floppy diskette that accompanies your upgrade card.