HP LH4r HP Netserver LPr Installation Guide - Page 83

screws that attach each end of the NetServer LPr front panel to the rack.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

Chapter 9 Mounting the Server in the Rack NOTE The power supply will continue to provide standby current to the NetServer until the power cable is disconnected. 3. Disconnect the power cable and, if necessary, all interface connectors from the rear panel. You may want to label these to support reassembly. 4. Remove the front bezel as described in Chapter 3. 5. Once the front bezel is removed, use a T25 Torx driver to remove the two screws that attach each end of the NetServer LPr front panel to the rack. They are at the left and right ends of the front panel. NOTE The rear brackets (see Figure 9-13) stay installed while the LPr is removed from the rack. The rear brackets serve to dampen vibration. Figure 9-14. Remove Screws Holding NetServer to Rack Front Columns 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Chapter 9
Mounting the Server in the Rack
75
NOTE
The power supply will continue to provide standby current to
the NetServer until the power cable is disconnected.
3.
Disconnect the power cable and, if necessary, all interface connectors
from the rear panel. You may want to label these to support reassembly.
4.
Remove the front bezel as described in Chapter 3.
5.
Once the front bezel is removed, use a T25 Torx driver to remove the two
screws that attach each end of the NetServer LPr front panel to the rack.
They are at the left and right ends of the front panel.
NOTE
The rear brackets (see Figure 9-13) stay installed while the
LPr is removed from the rack. The rear brackets serve to
dampen vibration.
Figure 9-14. Remove Screws Holding NetServer to Rack Front Columns