HP LH4r HP Netserver LPr Installation Guide - Page 60

Open the NetServer LPr

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Chapter 8 Installing Additional Processors The upgrade kit should include : • Processor Module • Voltage Regulator Module (VRM) • HP NetServer Navigator CD-ROM • HP NetServer LPr Processor Upgrade Guide NOTE Be sure to keep the bag around the processor sealed until you are ready to install the module. Open the NetServer LPr 1. Log off all users. Back up files. Follow instructions in your network operating system (NOS) documentation to gracefully shut down all networking software and applications. 2. Press the power switch on the HP NetServer's control panel when prompted by the operating system. 3. Disconnect the power cables and signal cables and, if necessary, label them to support reassembly. WARNING The power supply will continue to provide standby current to the NetServer until the power cable is disconnected. 4. Remove the NetServer from the rack. See the last section in Chapter 9. 5. Remove the top cover from the NetServer. See Chapter 3, "Opening and Closing the HP NetServer LPr." CAUTION Wear a wrist strap and use a static-dissipating work surface connected to the chassis when handling components. Ensure that the metal of the wrist strap contacts your skin. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Chapter 8
Installing Additional Processors
52
The upgrade kit should include:
•
Processor Module
•
Voltage Regulator Module (VRM)
•
HP NetServer Navigator CD-ROM
•
HP NetServer LPr Processor Upgrade Guide
NOTE
Be sure to keep the bag around the processor sealed until you
are ready to install the module.
Open the NetServer LPr
1.
Log off all users. Back up files. Follow instructions in your network
operating system (NOS) documentation to gracefully shut down all
networking software and applications.
2.
Press the power switch on the HP NetServer’s control panel when
prompted by the operating system.
3.
Disconnect the power cables and signal cables and, if necessary, label
them to support reassembly.
WARNING
The power supply will continue to provide standby current to
the NetServer until the power cable is disconnected.
4.
Remove the NetServer from the rack. See the last section in Chapter 9.
5.
Remove the top cover from the NetServer. See Chapter 3, "Opening and
Closing the HP NetServer LPr."
CAUTION
Wear a wrist strap and use a static-dissipating work surface
connected to the chassis when handling components. Ensure
that the metal of the wrist strap contacts your skin.