HP LaserJet Managed MFP E82540-E82560 On-Site Installation Guide - Page 88

Finishers, Install the Inner Finisher on the HP Color LaserJet MFP E87640, E87650, E87660

Get HP LaserJet Managed MFP E82540-E82560 PDF manuals and user guides View all HP LaserJet Managed MFP E82540-E82560 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

Finishers Install the Inner Finisher on the HP Color LaserJet MFP E87640, E87650, E87660 . Click here to view a video of this procedure. CAUTION: The engine assembly is heavy and requires four people to lift. Please review the LaserJet A3 videos for a complete understanding of the installation of each device. Use these checklists as a reminder of the steps demonstrated in the videos. Table 8-5 On-site final setup inner finisher on the HP Color LaserJet MFP E87640, E87650, E87660 ❑ Remove the duplex turn around support. TIP: Squeeze both sides toward the middle to remove the support. ❑ Remove the two paper settling guides. ❑ Gently lift the hook and remove the bin full actuator from the first exit. ❑ Remove two screws on the left side of the power button cover. ❑ Remove two screws at the front of the face-down bin (one screw requires a stubby JIS#2 driver). ❑ Pull OUT at the top to remove the left side of the power button cover. NOTE: A tab on the lower edge of the cover engages with a slot on the engine. ❑ Snap off the upper left cover. ❑ Lift and pull out to remove the output bin. ❑ Reinstall the left side of the power button cover. ❑ Remove the gray cover on the back wall under the scanner by removing four screws. NOTE: The two screws have a stick-on covers. ❑ Unpack the inner finisher and locate the second exit bin full assembly. ❑ Locate the pins on the rear and the three tabs along the length of the bin full sensor assembly. ❑ Locate the corresponding holes and the slots on the second exit assembly. ❑ Insert the tabs and slide the assembly toward the rear to fit the pins into the holes. ❑ Install one self-tapping screw at the front to secure the bin full sensor assembly. ❑ Connect the bin full sensory assembly cable to the engine. ❑ Reinstall the gray cover on the back wall under the scanner by installing 4 screws and four screw covers. ❑ Locate the wavy roller retainer. TIP: It looks like an upside down letter "U" with hooks on the ends. ❑ Push down and hold the middle roller on the first exit assembly. ❑ Install the retainer to hold the middle roller down. ❑ Locate the slide rails. ❑ Align the slides to the locator pins located on the top of the engine. NOTE: The white plastic end guide faces left. 82 Chapter 8 Complete installation procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Finishers
Install the Inner Finisher on the HP Color LaserJet MFP E87640, E87650, E87660
.
Click here to view a video of this procedure.
CAUTION:
The engine assembly is heavy and requires four people to lift.
Please review the LaserJet A3 videos for a complete understanding of the installation of each device. Use these
checklists as a reminder of the steps demonstrated in the videos.
Table 8-5
On-site final setup inner finisher on the HP Color LaserJet MFP E87640, E87650, E87660
❑
Remove the duplex turn around support.
TIP:
Squeeze both sides toward the middle to remove the support.
❑
Remove the two paper settling guides.
❑
Gently lift the hook and remove the bin full actuator from the first exit.
❑
Remove two screws on the left side of the power button cover.
❑
Remove two screws at the front of the face-down bin (one screw requires a stubby JIS#2 driver).
❑
Pull OUT at the top to remove the left side of the power button cover.
NOTE:
A tab on the lower edge of the cover engages with a slot on the engine.
❑
Snap off the upper left cover.
❑
Lift and pull out to remove the output bin.
❑
Reinstall the left side of the power button cover.
❑
Remove the gray cover on the back wall under the scanner by removing four screws.
NOTE:
The two screws have a stick-on covers.
❑
Unpack the inner finisher and locate the second exit bin full assembly.
❑
Locate the pins on the rear and the three tabs along the length of the bin full sensor assembly.
❑
Locate the corresponding holes and the slots on the second exit assembly.
❑
Insert the tabs and slide the assembly toward the rear to fit the pins into the holes.
❑
Install one self-tapping screw at the front to secure the bin full sensor assembly.
❑
Connect the bin full sensory assembly cable to the engine.
❑
Reinstall the gray cover on the back wall under the scanner by installing 4 screws and four screw covers.
❑
Locate the wavy roller retainer.
TIP:
It looks like an upside down letter “U” with hooks on the ends.
❑
Push down and hold the middle roller on the first exit assembly.
❑
Install the retainer to hold the middle roller down.
❑
Locate the slide rails.
❑
Align the slides to the locator pins located on the top of the engine.
NOTE:
The white plastic end guide faces left.
82
Chapter 8
Complete installation procedures
ENWW