HP LaserJet Managed MFP E82540-E82560 On-Site Installation Guide - Page 89

Install the Inner Punch, Click to view a video of this procedure.

Get HP LaserJet Managed MFP E82540-E82560 PDF manuals and user guides View all HP LaserJet Managed MFP E82540-E82560 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Table 8-5 On-site final setup inner finisher on the HP Color LaserJet MFP E87640, E87650, E87660 (continued) ❑ Use a short stubby JIS#2 drive to install three screw in each side. NOTE: These are self-tapping screws and require downward force to tap the holes. CAUTION: The inner rails have sharp edges. TIP: Slide the inner rails to the right to make the installation of the inner finisher easier. ❑ Position the inner finisher against the back wall of the opening. ❑ Hold level and then push IN to engage the unit in the slides. ❑ Open the front door and release the latch. ❑ Pull the finisher out and then back in to verify it is properly engaged with the slides. ❑ Remove stapler shipping lock label and remove shipping lock screw. ❑ Remove connector cover on the left side of MFP. ❑ Connect the inner finisher cable to the MFP. ❑ Locate the output tray. NOTE: Four pins on the bottom of the tray need to be aligned with the holes on the support brackets. NOTE: Push down firmly to engage the pins into the holes on the bracket. NOTE: Lift the output finger assembly when installing the tray. ❑ Install the tray on the support brackets and push down firmly to seat the pins in the holes. ❑ Hold the tray from above while installing the self-taping screws from below. Install the Inner Punch Click to view a video of this procedure. Please review the LaserJet A3 videos for a complete understanding of the installation of each device. Use these checklists as a reminder of the steps demonstrated in the videos. CAUTION: The engine assembly is heavy and requires four people to lift. NOTE: The inner punch must be purchased separately and is installed in the inner finisher. This is a checklist for installing the inner punch into a new inner finisher. NOTE: There are three different hole punch accessories that can be added to the Inner finisher 2/3. 2/4 and Swedish. Table 8-6 On-site final setup inner finisher punch ❑ Unpack the inner finisher and remove all the blue packing tape. ❑ Open the inner finisher front door. ❑ Unlatch and open the jam access area (also know as the dummy punch). ❑ Remove and discard the mylar surrounding the latch handle. ❑ Use a piece of blue tape to hold the latch in the open position. ❑ Locate and remove the e-clip and plastic washer just behind the lever. ENWW Finishers 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Table 8-5
On-site final setup inner finisher on the HP Color LaserJet MFP E87640, E87650, E87660 (continued)
❑
Use a short stubby JIS#2 drive to install three screw in each side.
NOTE:
These are self-tapping screws and require downward force to tap the holes.
CAUTION:
The inner rails have sharp edges.
TIP:
Slide the inner rails to the right to make the installation of the inner finisher easier.
❑
Position the inner finisher against the back wall of the opening.
❑
Hold level and then push IN to engage the unit in the slides.
❑
Open the front door and release the latch.
❑
Pull the finisher out and then back in to verify it is properly engaged with the slides.
❑
Remove stapler shipping lock label and remove shipping lock screw.
❑
Remove connector cover on the left side of MFP.
❑
Connect the inner finisher cable to the MFP.
❑
Locate the output tray.
NOTE:
Four pins on the bottom of the tray need to be aligned with the holes on the support brackets.
NOTE:
Push down firmly to engage the pins into the holes on the bracket.
NOTE:
Lift the output finger assembly when installing the tray.
❑
Install the tray on the support brackets and push down firmly to seat the pins in the holes.
❑
Hold the tray from above while installing the self-taping screws from below.
Install the Inner Punch
Click to view a video of this procedure.
Please review the LaserJet A3 videos for a complete understanding of the installation of each device. Use these
checklists as a reminder of the steps demonstrated in the videos.
CAUTION:
The engine assembly is heavy and requires four people to lift.
NOTE:
The inner punch must be purchased separately and is installed in the inner finisher. This is a checklist for
installing the inner punch into a new inner finisher.
NOTE:
There are three different hole punch accessories that can be added to the Inner finisher 2/3. 2/4 and
Swedish.
Table 8-6
On-site final setup inner finisher punch
❑
Unpack the inner finisher and remove all the blue packing tape.
❑
Open the inner finisher front door.
❑
Unlatch and open the jam access area (also know as the dummy punch).
❑
Remove and discard the mylar surrounding the latch handle.
❑
Use a piece of blue tape to hold the latch in the open position.
❑
Locate and remove the e-clip and plastic washer just behind the lever.
ENWW
Finishers
83