HP LaserJet Managed MFP E82540-E82560 On-Site Installation Guide - Page 91

Stapler/Stacker Finisher

Get HP LaserJet Managed MFP E82540-E82560 PDF manuals and user guides View all HP LaserJet Managed MFP E82540-E82560 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Stapler/Stacker Finisher Click here to view a video of this procedure. Please review the LaserJet A3 videos for a complete understanding of the installation of each device. Use these checklists as a reminder of the steps demonstrated in the videos. NOTE: There are three different hole punch accessories that can be added to the Stapler/Stacker finisher 2/3. 2/4 and Swedish. Stapler/Stacker Finisher Table 8-7 On-site final setup stapler/stacker ❑ Power down the MFP. ❑ Unpack finisher, bridge and attachment hardware. NOTE: On the engine, remove the bin full actuator, paper settling arms and face down bin. ❑ Install the bridge (IPTU) on the engine. Secure with one screw. Click here to view a video of this procedure. ❑ Remove the packing foam and tape from the finisher. ❑ Open the top cover on finisher and remove the foam and tape inside the paper path. ❑ Open front door on finisher and remove packing foam and tape inside door.. ❑ Remove the stapler shipping lock screw and label. ❑ Rotate the green wheel to the left until the spring loaded white tab is exposed under the stapler. ❑ Rotate the green wheel to the right until the stapler moves back to the front position and stops. ❑ While holding the green wheel, insert the staple cartridge holder into the stapler. ❑ Hang the lower tray support brackets on the horizontal bracket on the output side of the finisher. ❑ Secure each bracket with one screw. ❑ Note the alignment pins on the bottom of the tray and the corresponding holes on the support brackets. ❑ Position the tray over the brackets and push down firmly to seat the pins in the holes. ❑ While holding the tray from above, install four screws to secure the tray to the support brackets. ❑ Note the four tabs. Install the upper tray into the slots. ❑ Install front (F) and the rear (R) and the finisher attachment brackets on the left side of the engine. ❑ Secure with two screw in each bracket. ❑ Peel the cover off the connector near the rear bracket. ❑ Position the finisher near the left side of the engine and connect the two cables. ❑ Open the finisher front door and pull out the locking rail until it stops. ENWW Finishers 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Stapler/Stacker Finisher
Click here to view a video of this procedure
.
Please review the LaserJet A3 videos for a complete understanding of the installation of each device. Use these
checklists as a reminder of the steps demonstrated in the videos.
NOTE:
There are three different hole punch accessories that can be added to the Stapler/Stacker finisher 2/3.
2/4 and Swedish.
Stapler/Stacker Finisher
Table 8-7
On-site final setup stapler/stacker
❑
Power down the MFP.
❑
Unpack finisher, bridge and attachment hardware.
NOTE:
On the engine, remove the bin full actuator, paper settling arms and face down bin.
❑
Install the bridge (IPTU) on the engine. Secure with one screw.
Click here to view a video of this procedure.
❑
Remove the packing foam and tape from the finisher.
❑
Open the top cover on finisher and remove the foam and tape inside the paper path.
❑
Open front door on finisher and remove packing foam and tape inside door..
❑
Remove the stapler shipping lock screw and label.
❑
Rotate the green wheel to the left until the spring loaded white tab is exposed under the stapler.
❑
Rotate the green wheel to the right until the stapler moves back to the front position and stops.
❑
While holding the green wheel, insert the staple cartridge holder into the stapler.
❑
Hang the lower tray support brackets on the horizontal bracket on the output side of the finisher.
❑
Secure each bracket with one screw.
❑
Note the alignment pins on the bottom of the tray and the corresponding holes on the support brackets.
❑
Position the tray over the brackets and push down firmly to seat the pins in the holes.
❑
While holding the tray from above, install four screws to secure the tray to the support brackets.
❑
Note the four tabs. Install the upper tray into the slots.
❑
Install front (F) and the rear (R) and the finisher attachment brackets on the left side of the engine.
❑
Secure with two screw in each bracket.
❑
Peel the cover off the connector near the rear bracket.
❑
Position the finisher near the left side of the engine and connect the two cables.
❑
Open the finisher front door and pull out the locking rail until it stops.
ENWW
Finishers
85