HP LaserJet Managed MFP E82540-E82560 On-Site Installation Guide - Page 92

Booklet Maker Finisher with punch

Get HP LaserJet Managed MFP E82540-E82560 PDF manuals and user guides View all HP LaserJet Managed MFP E82540-E82560 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Table 8-7 On-site final setup stapler/stacker (continued) ❑ Align the brackets on the engine to the holes on the finisher and roll the finisher against the engine. ❑ Push the locking rail in and install one screw to secure the finisher to the engine. NOTE: If the locking rail won't slide in easily, adjust the casters on the finisher to change the height. NOTE: Check the vertical gap between the finisher and the engine. Adjust the casters for an equal gap from top to bottom. NOTE: Remove the finisher from the engine if the MFP needs to be moved anything more than a very short distance. Booklet Maker Finisher with punch Click here to view a video of this procedure. Please review the LaserJet A3 videos for a complete understanding of the installation of each device. Use these checklists as a reminder of the steps demonstrated in the videos. NOTE: There are three different hole punch accessories that can be added to the Booklet Maker finisher 2/3. 2/4 and Swedish. . Table 8-8 On-site final setup booklet maker finisher with punch ❑ Power down the MFP. ❑ Unpack finisher, bridge and attachment hardware. NOTE: On the engine, remove the bin full actuator, paper settling arms and face down bin. ❑ Install the bridge (IPTU) on the engine. Secure with one screw. Click here to view a video of this procedure. ❑ Remove packing foam and tape from the finisher. ❑ Open the top cover and remove the foam and tape inside the paper path. ❑ Locate and remove the shipping bracket for the booklet maker. Use one screw to store the bracket on the frame. ❑ Open the front door on the finisher and remove all foam and tape inside the finisher. ❑ Pull out the booklet maker and install two staple cartridge holders in the top of the booklet maker. ❑ Slide the booklet maker into the finisher. ❑ Remove the stapler lock screw and label. ❑ Rotate the green wheel to the left until the spring loaded white tab is exposed under the stapler. ❑ Rotate the green wheel to the right until the stapler moves back to the front position and stops. ❑ While holding the green wheel, insert the staple cartridge holder into the stapler. ❑ Follow these steps to install the optional hole punch. ❑ Remove two screws and remove the punch unit access panel on the rear of the finisher. ❑ Remove two screws and remove the "dummy" punch unit. NOTE: Save the dummy punch in the event the hole punch fails; it's needed if the hole punch is removed. ❑ Locate the alignment pin and tab at the front of the punch unit and the mounting bracket at the rear. NOTE: Be careful when handling the punch unit. Do not damage the mylar guides or the encoder wheel. 86 Chapter 8 Complete installation procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Table 8-7
On-site final setup stapler/stacker (continued)
❑
Align the brackets on the engine to the holes on the finisher and roll the finisher against the engine.
❑
Push the locking rail in and install one screw to secure the finisher to the engine.
NOTE:
If the locking rail won’t slide in easily, adjust the casters on the finisher to change the height.
NOTE:
Check the vertical gap between the finisher and the engine. Adjust the casters for an equal gap from top to bottom.
NOTE:
Remove the finisher from the engine if the MFP needs to be moved anything more than a very short distance.
Booklet Maker Finisher with punch
Click here to view a video of this procedure.
Please review the LaserJet A3 videos for a complete understanding of the installation of each device. Use these
checklists as a reminder of the steps demonstrated in the videos.
NOTE:
There are three different hole punch accessories that can be added to the Booklet Maker finisher 2/3.
2/4 and Swedish.
.
Table 8-8
On-site final setup booklet maker finisher with punch
❑
Power down the MFP.
❑
Unpack finisher, bridge and attachment hardware.
NOTE:
On the engine, remove the bin full actuator, paper settling arms and face down bin.
❑
Install the bridge (IPTU) on the engine. Secure with one screw.
Click here to view a video of this procedure.
❑
Remove packing foam and tape from the finisher.
❑
Open the top cover and remove the foam and tape inside the paper path.
❑
Locate and remove the shipping bracket for the booklet maker. Use one screw to store the bracket on the frame.
❑
Open the front door on the finisher and remove all foam and tape inside the finisher.
❑
Pull out the booklet maker and install two staple cartridge holders in the top of the booklet maker.
❑
Slide the booklet maker into the finisher.
❑
Remove the stapler lock screw and label.
❑
Rotate the green wheel to the left until the spring loaded white tab is exposed under the stapler.
❑
Rotate the green wheel to the right until the stapler moves back to the front position and stops.
❑
While holding the green wheel, insert the staple cartridge holder into the stapler.
❑
Follow these steps to install the optional hole punch.
❑
Remove two screws and remove the punch unit access panel on the rear of the finisher.
❑
Remove two screws and remove the “dummy” punch unit.
NOTE:
Save the dummy punch in the event the hole punch fails; it’s needed if the hole punch is removed.
❑
Locate the alignment pin and tab at the front of the punch unit and the mounting bracket at the rear.
NOTE:
Be careful when handling the punch unit. Do not damage the mylar guides or the encoder wheel.
86
Chapter 8
Complete installation procedures
ENWW