HP LaserJet Managed MFP E82540-E82560 On-Site Installation Guide - Page 93

Installation of HP LaserJet job separator

Get HP LaserJet Managed MFP E82540-E82560 PDF manuals and user guides View all HP LaserJet Managed MFP E82540-E82560 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

Table 8-8 On-site final setup booklet maker finisher with punch (continued) ❑ Carefully slide the punch unit into the finisher. Align the mounting bracket at the rear. NOTE: The punch unit is properly seated when the mounting bracket at the rear is flush against the finisher frame. NOTE: The orientation of the pins on the connector. While supporting the connector on the finisher side, insert the hole punch cable connector. ❑ Install one screw to secure the punch unit in the finisher. ❑ Replace the punch unit access panel and secure with two screws. ❑ Open the front door of the finisher and install the punch waste bin label. ❑ Pry the cover out of the punch waste bin opening and install the punch waste bin. ❑ Hang the lower tray support brackets on the horizontal bracket on the output side of the finisher. ❑ Secure each one with a screw. ❑ Note the alignment pins on the bottom of the tray and the corresponding holes on the support brackets. ❑ Position the tray over the brackets and push down firmly to seat the pins in the holes. ❑ While holding the tray from above, install four screws to secure the tray to the support brackets. ❑ Note the four tabs, install the upper tray into the slots. ❑ Install the front (F) and the rear (R) finisher attachment brackets on the left side of the engine. ❑ Secure with two screws in each bracket. ❑ Peel the cover off the connector near the rear bracket. ❑ Position the finisher near the left side of the engine and connect the two cables. ❑ Open the finisher front door and pull out the locking rail until it stops. ❑ Align the brackets on the engine to the holes on the finisher and roll the finisher against the engine. ❑ Push the locking rail in and install one screw to secure the finisher to the engine. NOTE: If the locking rail won't slide in easily, adjust the casters on the finisher to change the height. NOTE: Check the vertical gap between the finisher and the engine. Adjust the casters for an equal gap from top to bottom. NOTE: Remove the finisher from the engine if the MFP needs to be moved anything more than a very short distance. Installation of HP LaserJet job separator NOTE: There is no video available to show the procedure of how to install the job separator. CAUTION: The engine assembly is heavy and requires four people to lift. Use this checklist to perform the installation of the job separator. Table 8-9 On-site final setup job separator ❑ Remove the duplex turn around support. TIP: Squeeze on both sides toward the middle to remove the support. ❑ Remove two screws on the left side of the power button cover. ❑ Remove two screws at the front of the face-down bin (output bin) (one screw will require a stubby JIS#2 dirver). ENWW Finishers 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Table 8-8
On-site final setup booklet maker finisher with punch (continued)
❑
Carefully slide the punch unit into the finisher. Align the mounting bracket at the rear.
NOTE:
The punch unit is properly seated when the mounting bracket at the rear is flush against the finisher frame.
NOTE:
The orientation of the pins on the connector. While supporting the connector on the finisher side, insert the hole
punch cable connector.
❑
Install one screw to secure the punch unit in the finisher.
❑
Replace the punch unit access panel and secure with two screws.
❑
Open the front door of the finisher and install the punch waste bin label.
❑
Pry the cover out of the punch waste bin opening and install the punch waste bin.
❑
Hang the lower tray support brackets on the horizontal bracket on the output side of the finisher.
❑
Secure each one with a screw.
❑
Note the alignment pins on the bottom of the tray and the corresponding holes on the support brackets.
❑
Position the tray over the brackets and push down firmly to seat the pins in the holes.
❑
While holding the tray from above, install four screws to secure the tray to the support brackets.
❑
Note the four tabs, install the upper tray into the slots.
❑
Install the front (F) and the rear (R) finisher attachment brackets on the left side of the engine.
❑
Secure with two screws in each bracket.
❑
Peel the cover off the connector near the rear bracket.
❑
Position the finisher near the left side of the engine and connect the two cables.
❑
Open the finisher front door and pull out the locking rail until it stops.
❑
Align the brackets on the engine to the holes on the finisher and roll the finisher against the engine.
❑
Push the locking rail in and install one screw to secure the finisher to the engine.
NOTE:
If the locking rail won’t slide in easily, adjust the casters on the finisher to change the height.
NOTE:
Check the vertical gap between the finisher and the engine. Adjust the casters for an equal gap from top to bottom.
NOTE:
Remove the finisher from the engine if the MFP needs to be moved anything more than a very short distance.
Installation of HP LaserJet job separator
NOTE:
There is no video available to show the procedure of how to install the job separator.
CAUTION:
The engine assembly is heavy and requires four people to lift.
Use this checklist to perform the installation of the job separator.
Table 8-9
On-site final setup job separator
❑
Remove the duplex turn around support.
TIP:
Squeeze on both sides toward the middle to remove the support.
❑
Remove two screws on the left side of the power button cover.
❑
Remove two screws at the front of the face-down bin (output bin) (one screw will require a stubby JIS#2 dirver).
ENWW
Finishers
87