Home » HP Manuals » Desktops » HP ML150 » Manual Viewer

HP ML150 HP ProLiant ML100 Series Server User Guide - Page 48

Installing an operating system, Installing a supported Microsoft® Windows® OS

UPC - 884420743644

Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Installing an operating system To install an OS, download the SATA RAID driver and create a driver diskette with the software and instructions from the HP website (http://www.hp.com/support). Installing a supported Microsoft® Windows® OS 1. Insert the OS CD and reboot the system. 2. When prompted, press the F6 key to install a third-party driver. NOTE: Press F6 within 5 seconds to enable the system to recognize the controller. If the system fails to recognize the controller, restart this procedure. 3. Insert the SATA RAID driver diskette created earlier. The system prompts the next action. 4. Press the S key to specify the driver from the diskette. Then, press the Enter key. The OS searches the diskette for a suitable driver. 5. After locating the Adaptec Embedded Serial ATA HostRAID driver, press Enter. 6. Follow the remaining on-screen instructions to complete the installation. Installing a supported Linux OS To install a supported Linux OS when using the HP Embedded SATA RAID controller, see the OS documentation. Software and configuration utilities 48

Section	Page
HP ProLiant ML100 Series Server User Guide	1
Notice	2
Contents	3
Operations	7
Power up the server	7
Power down the server	7
Remove the access panel	7
Remove the tower bezel (ML110 G6 servers)	8
Remove the tower bezel (ML150 G6 servers)	8
Setup	9
Optional installation services	9
Rack planning resources	9
Optimum environment	9
Space and airflow requirements	10
Temperature requirements	11
Power requirements	11
Electrical grounding requirements	11
Rack warnings	12
Installing hardware options	12
Powering up and configuring the server	12
Installing the operating system	12
Registering the server	13
Hardware options installation	14
Introduction	14
Processor option	14
SAS and SATA hard drive options	17
Hard drive LED cable (ML150 G6 servers and ML110 G6 Servers)	17
Removable media device option (ML110 G6 servers)	18
Removable media device option (ML150 G6 servers)	20
Memory options (ML110 G6 servers)	21
Memory subsystem architecture (ML110 G6 servers)	21
Single- and dual-rank DIMMs (ML110 G6 servers)	22
DIMM identification (ML110 G6 servers)	22
UDIMM maximum memory configurations (ML110 G6 servers)	23
General DIMM slot population guidelines (ML110 G6 servers)	23
Memory options (ML150 G6 servers)	24
Memory subsystem architecture	24
Single-, dual-, and quad-rank DIMMs	24
DIMM identification	25
Memory configurations	25
RDIMM maximum memory configurations	26
UDIMM maximum memory configurations	26
Advanced ECC memory configuration	26
Lockstep memory configuration	26
General DIMM slot population guidelines	26
Advanced ECC population guidelines	27
Single-processor Advanced ECC population order	27
Multi-processor Advanced ECC population order	27
Lockstep Memory population guidelines	27
Single-processor Lockstep population order	28
Multi-processor Lockstep population order	28
Installing DIMMs	28
Expansion board options	29
Installing a storage controller	32
Battery-backed write cache battery pack option	32
Installing the FBWC module and capacitor pack	35
HP Trusted Platform Module option	36
Installing the Trusted Platform Module board	37
Retaining the recovery key/password	39
Enabling the Trusted Platform Module	39
Software and configuration utilities	40
ROM-Based Setup Utility	40
Using RBSU	40
Auto-configuration process	40
Boot options	41
BIOS Serial Console	41
Array Configuration Utility	41
Option ROM Configuration for Arrays	42
HP Insight Diagnostics	42
Management tools	42
ROMPaq utility	42
Lights-Out 100i technology	43
HP Integrated Lights-Out Virtual Floppy and CD-ROM drives	43
USB support	43
Remote support and analysis tools	43
HP Insight Remote Support software	43
Keeping the system current	44
Drivers	44
Operating System Version Support	44
Subscriber's choice	44
Embedded SATA RAID feature	45
Configuring the SATA RAID feature	45
Enabling the SATA RAID feature in RBSU	45
Creating a RAID volume	45
Installing the embedded SATA RAID driver	46
Required hardware	46
Diskette and CD-ROM drive options	46
HP Integrated Lights-Out Virtual Floppy and CD-ROM drives	46
USB diskette and CD-ROM drives	46
Creating a diskette image	47
Installing the Embedded SATA RAID driver with a USB diskette drive	47
Installing the Embedded SATA RAID driver using Virtual Floppy	47
Installing an operating system	48
Installing a supported Microsoft® Windows® OS	48
Installing a supported Linux OS	48
Troubleshooting	49
Pre-diagnostic steps	49
Important safety information	49
Symbols on equipment	49
Warnings and cautions	50
Symptom information	51
Preparing the server for diagnosis	51
Common problem resolution	52
Loose connections	52
Service notifications	52
Firmware updates	52
DIMM handling guidelines	53
SAS and SATA hard drive guidelines	53
SAS and SATA hard drive LED combinations	53
Troubleshooting flowcharts	54
Start diagnosis flowchart	55
General diagnosis flowchart	55
Power-on problems flowchart	57
POST problems flowchart	59
OS boot problems flowchart	61
Server fault indications flowchart	62
Hardware problems	64
Power problems	65
Power source problems	65
Power supply problems	65
UPS problems	65
UPS is not working properly	65
Low battery warning is displayed	66
One or more LEDs on the UPS is red	66
General hardware problems	66
Problems with new hardware	66
Unknown problem	67
Third-party device problems	67
Testing the device	68
Internal system problems	68
CD-ROM and DVD drive problems	68
System does not boot from the drive	68
Data read from the drive is inconsistent, or drive cannot read data	69
Drive is not detected	69
DAT drive problems	69
Sense error codes are displayed	69
DAT drive error or failure occurs	69
DAT drive is providing poor performance	69
Latest firmware indicates a defective tape, or head clogs occur regularly	69
Other errors are occurring	70
Diskette drive problems	70
Diskette drive light stays on	70
A problem has occurred with a diskette transaction	70
Diskette drive cannot read a diskette	70
Drive is not found	70
Non-system disk message is displayed	70
Diskette drive cannot write to a diskette	70
Fan problems	71
General fan problems are occurring	71
Hard drive problems	71
System completes POST but hard drive fails	71
No hard drives are recognized	71
Hard drive is not recognized by the server	72
A new hard drive is not recognized	72
Data is inaccessible	72
Server response time is slower than usual	72
Memory problems	73
General memory problems are occurring	73
Server is out of memory	73
Memory count error exists	73
Server fails to recognize existing memory	73
Server fails to recognize new memory	74
PPM problems	74
Processor problems	74
System open circuits and short circuits	75
External device problems	75
Video problems	75
Screen is blank for more than 60 seconds after you power up the server	75
Monitor does not function properly with energy saver features	76
Video colors are wrong	76
Slow-moving horizontal lines are displayed	76
Audio problems	76
Printer problems	77
Printer does not print	77
Printer output is garbled	77
Mouse and keyboard problems	77
Modem problems	77
No dial tone exists	77
No response occurs when you type AT commands	78
AT commands are not visible	78
Data is displayed as garbled characters after the connection is established	78
Modem does not answer an incoming call	78
Modem does not connect to another modem	78
Modem disconnects while online	78
AT command initialization string is not working	79
Connection errors are occurring	79
You are unable to connect to an online subscription service	79
You are unable to connect at 56 Kbps	79
Network controller problems	79
Network controller is installed but not working	79
Network controller has stopped working	80
Network controller stopped working when an expansion board was added	80
Problems are occurring with the network interconnect blades	81
Software problems	81
Operating system problems	81
Operating system locks up	81
General protection fault occurs	81
Errors are displayed in the error log	81
Problems occur after the installation of a service pack	82
Operating system updates	82
Restoring to a backed-up version	82
When to reconfigure or reload software	82
Linux operating systems	83
Application software problems	83
Software locks up	83
Errors occur after a software setting is changed	83
Errors occur after the system software is changed	83
Errors occur after an application is installed	83
Firmware maintenance	84
Types of ROM	84
System ROM	84
Automatic backup	84
Option ROMs	84
ROMPaq utility diskette or USB drive key	85
Current firmware versions	85
Updating firmware	85
Drivers	86
Contacting HP	86
Contacting HP technical support or an authorized reseller	86
Server information you need	86
Operating system information you need	87
Microsoft® operating systems	87
Linux operating systems	88
Battery	89
Regulatory compliance notices	91
Regulatory compliance identification numbers	91
Federal Communications Commission notice	91
FCC rating label	91
Class A equipment	91
Class B equipment	91
Declaration of conformity for products marked with the FCC logo, United States only	92
Modifications	92
Cables	92
Canadian notice (Avis Canadien)	93
European Union regulatory notice	93
Disposal of waste equipment by users in private households in the European Union	93
Japanese notice	94
BSMI notice	94
Korean notice	95
Chinese notice	95
Laser compliance	95
Battery replacement notice	95
Taiwan battery recycling notice	96
Power cord statement for Japan	96
Acoustics statement for Germany (Geräuschemission)	96
Electrostatic discharge	97
Preventing electrostatic discharge	97
Grounding methods to prevent electrostatic discharge	97
Technical support	98
HP contact information	98
Before you contact HP	98
Customer Self Repair	98
Acronyms and abbreviations	106