HP Surestore E Tape Library Model 6/60 HP SureStore E Tape Library Models 2/20 - Page 105

Configuring the Library for Fibre Channel, Fibre Channel, Main Menu, Administration

Get HP Surestore E Tape Library Model 6/60 PDF manuals and user guides View all HP Surestore E Tape Library Model 6/60 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

NOTE NOTE NOTE Library Administration Configuring the Library for Fibre Channel Configuring the Library for Fibre Channel Refer to Appendix C if you are unfamiliar with Fibre Channel terminology before beginning this procedure. The optional Fibre Channel interfaces in 20-slot, 40-slot, and 60-slot libraries serve as a bridge between SCSI and Fibre Channel. It is not necessary to connect the library to its Fibre Channel topology (arbitrated loop or fabric) before configuration. Configuration When Fibre Channel interfaces are installed in the library, device SCSI IDs cannot be changed from their factory default. Though you do not need to set SCSI IDs for Fibre Channel, you will need to configure Fibre Channel addressing. Main Menu -> Administration -> Change Configuration -> Fibre Channel 1. Enter the Fibre Channel menu. 2. Select the level where the Fibre Channel interface you want to configure is located. Use the [-] key to select a lower level in the library. Use the [+] key to select a higher level in the library. Select [OK] if the level is correct. Chapter 3 3-15 Library Administration

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
Library Administration
Configuring the Library for Fibre Channel
Chapter 3
3-15
Library Administration
Configuring the Library for Fibre Channel
NOTE
Refer to Appendix C if you are unfamiliar with Fibre Channel terminology
before beginning this procedure.
The optional Fibre Channel interfaces in 20-slot, 40-slot, and 60-slot
libraries serve as a bridge between SCSI and Fibre Channel.
NOTE
It is not necessary to connect the library to its Fibre Channel topology
(arbitrated loop or fabric) before configuration.
Configuration
NOTE
When Fibre Channel interfaces are installed in the library, device SCSI
IDs cannot be changed from their factory default.
Though you do not need to set SCSI IDs for Fibre Channel, you will need
to configure Fibre Channel addressing.
1.
Enter the
Fibre Channel
menu.
2.
Select the level where the Fibre Channel interface you want to
configure is located.
Use the
[-]
key to select a lower level in the library.
Use the
[+]
key to select a higher level in the library.
Select
[OK]
if the level is correct.
Main Menu
->
Administration
->
Change Configuration
->
Fibre Channel