HP Surestore E Tape Library Model 6/60 HP SureStore E Tape Library Models 2/20 - Page 23

Installing a Stand-Alone Library in a Rack, Removing the Cover

Get HP Surestore E Tape Library Model 6/60 PDF manuals and user guides View all HP Surestore E Tape Library Model 6/60 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Getting Started Library Installation Installing a Stand-Alone Library in a Rack NOTE NOTE Figure 1-1 Installing a Stand-Alone Library in a Rack For stand-alone installations, see "Connecting and Powering on the Library" on page 1-24. To install a stand-alone library in a rack, remove the cover and feet by following these steps: 1. Remove the following six screws (Figure 1-1): a. Four screws, one located at each of the four feet b. Two screws near the bottom of the library and in the back 2. Lift the cover off the library. The cover may fit tightly. If you cannot remove it easily, ease the sides out while lifting up on the cover. Removing the Cover Chapter 1 1-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
Library Installation
Installing a Stand-Alone Library in a Rack
Chapter 1
1-7
Getting Started
Installing a Stand-Alone Library in a Rack
NOTE
For stand-alone installations, see
“
Connecting and Powering on the
Library
”
on page 1-24.
To install a stand-alone library in a rack, remove the cover and feet by
following these steps:
1.
Remove the following six screws (Figure 1-1):
a.
Four screws, one located at each of the four feet
b.
Two screws near the bottom of the library and in the back
2.
Lift the cover off the library.
NOTE
The cover may fit tightly. If you cannot remove it easily, ease the sides out
while lifting up on the cover.
Figure 1-1
Removing the Cover