HP Tc2120 serhp server tc2120 operations and maintenance guide - english - Page 29

Installing a Disk Drive Tray Mounted

Get HP Tc2120 - Server - 256 MB RAM PDF manuals and user guides
UPC - 808736945332
View all HP Tc2120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Chapter 3 Refer to the documentation provided with the hard drive. Installing and Configuring NOTE If the hard disk drive (HDD) you are planning to install already has a mounting tray attached, you must remove it from the tray. 6. Install the hard disk drive as described below: a. Place the hard disk drive into the tray and use the screws provided to secure it to the tray from the bottom. b. Insert the hard disk drive assembly into the fourth shelf. See Figure 3-9. The tabs should snap into place when the drive is pushed all the way into the fourth shelf. Extra Screws Figure 3-9. Installing a Disk Drive (Tray Mounted) 7. Connect the data cable to the hard drive, as described below: o If mounting a third IDE hard drive, connect the secondary (IDE-2) cable to the hard drive. o If mounting a third SCSI hard drive, connect the SCSI cable to the drive and ensure all SCSI drives are connected to the SCSI cable. o There are five connectors on the standard SCSI cable; with four of the connectors intended for the three hard disk drives and one optional backup tape drive. The standard SCSI cable has a terminator at the end of the cable. 8. Connect the power cable to the rear of the hard disk drive. 9. Replace the upper bezel and left side cover. 10. Replace the external cables, and power cord, and then restore power to the server. The BIOS and SCSISelect utilities automatically detect the new hard drives (IDE or SCSI), but you should check the BIOS and SCSISelect settings and make changes as necessary. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
23
Chapter 3
Installing and Configuring
Refer to the documentation provided with the hard drive.
6.
Install the hard disk drive as described below:
a.
Place the hard disk drive into the tray and use the screws provided to secure it to the tray from the bottom.
b.
Insert the hard disk drive assembly into the fourth shelf. See
Figure 3-9
.
The tabs should snap into place when the drive is pushed all the way into the fourth shelf.
7.
Connect the data cable to the hard drive, as described below:
o
If mounting a third IDE hard drive, connect the secondary (IDE-2) cable to the hard drive.
o
If mounting a third SCSI hard drive, connect the SCSI cable to the drive and ensure all SCSI drives are
connected to the SCSI cable.
o
There are five connectors on the standard SCSI cable; with four of the connectors intended for the three
hard disk drives and one optional backup tape drive. The standard SCSI cable has a terminator at the end
of the cable.
8.
Connect the power cable to the rear of the hard disk drive.
9.
Replace the upper bezel and left side cover.
10.
Replace the external cables, and power cord, and then restore power to the server.
The BIOS and SCSISelect utilities automatically detect the new hard drives (IDE or SCSI), but you should
check the BIOS and SCSISelect settings and make changes as necessary.
NOTE
If the hard disk drive (HDD) you are planning to install
already has a mounting tray attached, you must remove it from
the tray.
Figure 3-9.
Installing a Disk Drive (Tray Mounted)
Extra
Screws