HP Tc2120 serhp server tc2120 operations and maintenance guide - english - Page 31

Heading2 - Installing an Optional Backup Tape Drive,

Get HP Tc2120 - Server - 256 MB RAM PDF manuals and user guides
UPC - 808736945332
View all HP Tc2120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Chapter 3 Installing and Configuring Extra Screws Figure 3-10. Installing an Optional CD-ROM or DVD Drive Installing an Optional Backup Tape Drive The optional HP SureStore DAT 24i backup tape drive is a single-ended device and may slow down the disk access time for the Ultra-160 SCSI drives. A second SCSI controller board may be required to separately control the backup tape drive. 1. If the server is already installed and operating, power-down the server. Refer to Chapter 1, Controls and Indicators. 2. Disconnect the power cables and any external cables connected to the server. If necessary, label each one to expedite re-assembly. 3. Remove the left side cover from the server. Refer to "Opening and Closing the hp server" earlier in this chapter. 4. Remove the upper front bezel. Refer to "Opening and Closing the hp server" earlier in this chapter. 5. Press in on both tab latches to release the third drive tray and pull it out at the same time. See Figure 3-11. 6. Remove the RFI shield from the third drive tray. See Figure 3-11. 7. Ensure that the backup tape drive is not terminated and ensure that the SCSI ID jumper is set for address = ID 3 on the tape drive. The optional HP SureStore DAT 24i backup tape drive is shipped with the default setting of SCSI address = ID 3. Refer to the documentation provided with the tape drive. 8. Install the backup tape drive, as described below: 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
25
Chapter 3
Installing and Configuring
Installing an Optional Backup Tape Drive
The optional HP SureStore DAT 24i backup tape drive is a single-ended device and may slow down the disk
access time for the Ultra-160 SCSI drives. A second SCSI controller board may be required to separately control
the backup tape drive.
1.
If the server is already installed and operating, power-down the server.
Refer to
Chapter 1‚ Controls and Indicators
.
2.
Disconnect the power cables and any external cables connected to the server.
If necessary, label each one to expedite re-assembly.
3.
Remove the left side cover from the server.
Refer to
“Opening and Closing the hp server”
earlier in this chapter.
4.
Remove the upper front bezel.
Refer to
“Opening and Closing the hp server”
earlier in this chapter.
5.
Press in on both tab latches to release the third drive tray and pull it out at the same time. See
Figure 3-11
.
6.
Remove the RFI shield from the third drive tray. See
Figure 3-11
.
7.
Ensure that the backup tape drive is not terminated and ensure that the SCSI ID jumper is set for address =
ID 3 on the tape drive.
The optional HP SureStore DAT 24i backup tape drive is shipped with the default setting of SCSI address
= ID 3. Refer to the documentation provided with the tape drive.
8.
Install the backup tape drive, as described below:
Figure 3-10.
Installing an Optional CD-ROM or DVD Drive
Extra
Screws