HP Tc2120 serhp server tc2120 operations and maintenance guide - english - Page 93

Heading2 - Removing a Hard Disk Drive (Drive Cage Mounted)

Get HP Tc2120 - Server - 256 MB RAM PDF manuals and user guides
UPC - 808736945332
View all HP Tc2120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

Chapter 7 6. Replace the upper bezel. Replacing Parts NOTE If this is the initial installation of a hard disk drive in this location, it is necessary to remove the bezel drive cover from the upper front bezel. 7. Replace the left side cover. 8. Replace the external cables and power cord. 9. Power on the server as described in Chapter 1, Controls and Indicators. Removing a Hard Disk Drive (Drive Cage Mounted) The replacement of the mass storage cage mounted drives is the same for IDE or SCSI devices. The first hard disk drive (IDE or SCSI) is always mounted in the top (shelf 5) of the hard disk drive cage. The second hard disk drive should be mounted just below it (shelf 6). CAUTION Install and remove connectors carefully, and avoid displacing any pins. 1. If the server is operating, power down the server. Refer to Chapter 1, Controls and Indicators for instructions. 2. Disconnect the power cord and any external cables connected to the server. If necessary, label each one to expedite re-assembly. 3. Remove the left side cover. 4. Disconnect the data and power connectors from the drive. 5. Press and release the retaining clips at the side of the drive cage. 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
87
Chapter 7
Replacing Parts
6.
Replace the upper bezel.
7.
Replace the left side cover.
8.
Replace the external cables and power cord.
9.
Power on the server as described in
Chapter 1‚ Controls and Indicators
.
Removing a Hard Disk Drive (Drive Cage Mounted)
The replacement of the mass storage cage mounted drives is the same for IDE or SCSI devices. The first hard
disk drive (IDE or SCSI) is always mounted in the top (shelf 5) of the hard disk drive cage. The second hard
disk drive should be mounted just below it (shelf 6).
1.
If the server is operating, power down the server.
Refer to
Chapter 1‚ Controls and Indicators
for instructions.
2.
Disconnect the power cord and any external cables connected to the server.
If necessary, label each one to expedite re-assembly.
3.
Remove the left side cover.
4.
Disconnect the data and power connectors from the drive.
5.
Press and release the retaining clips at the side of the drive cage.
NOTE
If this is the initial installation of a hard disk drive in this
location, it is necessary to remove the bezel drive cover from
the upper front bezel.
CAUTION
Install and remove connectors carefully, and avoid
displacing any pins.