HP Tc2120 serhp server tc2120 operations and maintenance guide - english - Page 32

CAUTION, any of the pins.

Get HP Tc2120 - Server - 256 MB RAM PDF manuals and user guides
UPC - 808736945332
View all HP Tc2120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Chapter 3 Installing and Configuring a. Place it into the tray and use the screws provided to secure it to the tray. See Figure 3-11. The optional HP SureStore DAT 24i backup tape drive is a single-ended drive and normally comes with the 5¼ inch mounting brackets installed on the tape drive. If the brackets are not pre-installed, follow the instructions provided with the tape drive to connect the 5¼-inch mounting brackets to the tape drive before installing the tape drive into the third drive tray. b. Insert the backup tape drive mounted in the tray into the third shelf. The tabs should snap into place when the third drive tray is pushed all of the way into the third shelf. CAUTION Install and remove connectors carefully, and avoid displacing any of the pins. 9. Connect the SCSI data and power cables to the rear of the backup tape drive. The SCSI data and power cables for the tape drive should already be routed to the tape drive. If they are not, locate the free SCSI and power connectors and route them to the tape drive. NOTE The slower speed of the tape drive may slow disk access time for the Ultra-160 SCSI drives. You should install an additional SCSI controller board to control the backup tape drive separately from the Ultra-160 SCSI drives. You may use the internal SCSI cable provided with the second SCSI controller board to connect to the tape drive. 10. Replace the upper bezel and the left side cover. 11. Replace the external cables, power cord, and then restore power to the server. The SCSISelect Utility automatically detects the new SCSI backup tape drive, but you should check the SCSISelect settings and make changes as necessary. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
26
Chapter 3
Installing and Configuring
a.
Place it into the tray and use the screws provided to secure it to the tray. See
Figure 3-11
.
The optional HP SureStore DAT 24i backup tape drive is a single-ended drive and normally comes with
the 5¼ inch mounting brackets installed on the tape drive. If the brackets are not pre-installed, follow
the instructions provided with the tape drive to connect the 5¼-inch mounting brackets to the tape drive
before installing the tape drive into the third drive tray.
b.
Insert the backup tape drive mounted in the tray into the third shelf.
The tabs should snap into place when the third drive tray is pushed all of the way into the third shelf.
9.
Connect the SCSI data and power cables to the rear of the backup tape drive.
The SCSI data and power cables for the tape drive should already be routed to the tape drive. If they are not,
locate the free SCSI and power connectors and route them to the tape drive.
10.
Replace the upper bezel and the left side cover.
11.
Replace the external cables, power cord, and then restore power to the server.
The SCSISelect Utility automatically detects the new SCSI backup tape drive, but you should check the
SCSISelect settings and make changes as necessary.
CAUTION
Install and remove connectors carefully, and avoid displacing
any of the pins.
NOTE
The slower speed of the tape drive may slow disk access time
for the Ultra-160 SCSI drives. You should install an additional
SCSI controller board to control the backup tape drive
separately from the Ultra-160 SCSI drives. You may use the
internal SCSI cable provided with the second SCSI controller
board to connect to the tape drive.