HP Tc2120 serhp server tc2120 operations and maintenance guide - english - Page 30

Heading2 - Installing an Optional CD-ROM or DVD Drive, rear of the chassis.

Get HP Tc2120 - Server - 256 MB RAM PDF manuals and user guides
UPC - 808736945332
View all HP Tc2120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Chapter 3 Installing and Configuring Installing an Optional CD-ROM or DVD Drive You may install an optional IDE CD-ROM or DVD drive in the third drive tray. The secondary IDE cable, which is connected to the IDE CD-ROM in the second drive tray, has an available connector that may be used for an IDE device in either the third or fourth tray. 1. If the server is operating, power down the server. Refer to Chapter 1, Controls and Indicators for instructions. 2. Disconnect the power cord and any external cables connected to the server. If necessary, label each one to expedite re-assembly. 3. Remove the left side cover. Refer to "Opening and Closing the hp server" earlier in this chapter. 4. Remove the upper bezel. Refer to "Opening and Closing the hp server" earlier in this chapter. 5. Press in on both tab latches to release the third drive tray and pull it out at the same time. See Figure 3-10. 6. Remove the RFI shield from the third drive tray. 7. Remove the CD-ROM from the shipping container. 8. Make any settings required by the CD-ROM documentation (primary or slave, etc.). 9. If not already mounted, place the CD-ROM into the CD-ROM tray and secure it using the four screws. 10. Guide the CD-ROM tray into the chassis opening, with the cable connectors of the CD-ROM toward the rear of the chassis. 11. Push the CD-ROM tray all the way into the chassis until the CD-ROM tray snaps into place. The two release tabs should click when in place. 12. At the rear of the CD-ROM, carefully connect the power and data cables. The IDE CD-ROM uses one connector on the cable from the IDE-2 connector, leaving one connector that may be used for an IDE device in the third tray. 13. Replace the upper bezel. 14. Replace the left side cover. 15. Replace the external cables and power cord. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
24
Chapter 3
Installing and Configuring
Installing an Optional CD-ROM or DVD Drive
You may install an optional IDE CD-ROM or DVD drive in the third drive tray. The secondary IDE cable,
which is connected to the IDE CD-ROM in the second drive tray, has an available connector that may be used
for an IDE device in either the third or fourth tray.
1.
If the server is operating, power down the server.
Refer to
Chapter 1‚ Controls and Indicators
for instructions.
2.
Disconnect the power cord and any external cables connected to the server.
If necessary, label each one to expedite re-assembly.
3.
Remove the left side cover.
Refer to
“Opening and Closing the hp server”
earlier in this chapter.
4.
Remove the upper bezel.
Refer to
“Opening and Closing the hp server”
earlier in this chapter.
5.
Press in on both tab latches to release the third drive tray and pull it out at the same time. See
Figure 3-10
.
6.
Remove the RFI shield from the third drive tray.
7.
Remove the CD-ROM from the shipping container.
8.
Make any settings required by the CD-ROM documentation (primary or slave, etc.).
9.
If not already mounted, place the CD-ROM into the CD-ROM tray and secure it using the four screws.
10.
Guide the CD-ROM tray into the chassis opening, with the cable connectors of the CD-ROM toward the
rear of the chassis.
11.
Push the CD-ROM tray all the way into the chassis until the CD-ROM tray snaps into place.
The two release tabs should click when in place.
12.
At the rear of the CD-ROM, carefully connect the power and data cables.
The IDE CD-ROM uses one connector on the cable from the IDE-2 connector, leaving one connector that
may be used for an IDE device in the third tray.
13.
Replace the upper bezel.
14.
Replace the left side cover.
15.
Replace the external cables and power cord.