HP Tc2120 serhp server tc2120 operations and maintenance guide - english - Page 97

Heading1 - Processor, seated by sliding a straight edge a pen, for example across

Get HP Tc2120 - Server - 256 MB RAM PDF manuals and user guides
UPC - 808736945332
View all HP Tc2120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

Chapter 7 4. Align the notches on the DIMM with the keys on the slot. Notches Keys Replacing Parts Retaining Latches DIMM Slot Figure 7-9. DIMM to Slot Alignment 5. Holding the DIMM at 90 degrees to the system board, press the DIMM fully into the slot until the retaining latches close. If the latches do not close, the DIMM is not inserted correctly. 6. Repeat Steps 1-5, to install all of the remaining DIMMs for your memory configuration. 7. Replace the left side cover. 8. Replace the external cables and power cord. 9. Power on the server, as described in Chapter 1, Controls and Indicators. If the DIMMs are not seated properly you may get a blank screen. NOTE Most DIMMs are dimensionally identical, so, if you have two or more DIMMs installed, you may verify all DIMMs are seated by sliding a straight edge (a pen, for example) across the top edges and verify it remains in continuous contact with all of the DIMMs. Processor Use the procedures in this section to remove and replace the heat sink-cooling fan and the processor. CAUTION Wear a wrist strap and use a static-dissipating work surface connected to the chassis when handling components. Ensure the metal of the wrist strap contacts your skin. 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
91
Chapter 7
Replacing Parts
4.
Align the notches on the DIMM with the keys on the slot.
5.
Holding the DIMM at 90 degrees to the system board, press the DIMM fully into the slot until the retaining
latches close.
If the latches do not close, the DIMM is not inserted correctly.
6.
Repeat Steps 1-5, to install all of the remaining DIMMs for your memory configuration.
7.
Replace the left side cover.
8.
Replace the external cables and power cord.
9.
Power on the server, as described in
Chapter 1‚ Controls and Indicators
.
If the DIMMs are not seated properly you may get a blank screen.
Processor
Use the procedures in this section to remove and replace the heat sink-cooling fan and the processor.
Figure 7-9.
DIMM to Slot Alignment
NOTE
Most DIMMs are dimensionally identical, so, if you have two
or more DIMMs installed, you may verify all DIMMs are
seated by sliding a straight edge (a pen, for example) across
the top edges and verify it remains in continuous contact with
all of the DIMMs.
CAUTION
Wear a wrist strap and use a static-dissipating work surface
connected to the chassis when handling components. Ensure
the metal of the wrist strap contacts your skin.
Notches
Retaining Latches
Keys
DIMM Slot