HP Xw8400 HP xw8400 Workstation - Service and Technical Reference Guide - Page 103

Processor heatsink, Removing the CPU heatsink

Get HP Xw8400 - Workstation - 4 GB RAM PDF manuals and user guides
UPC - 883585271085
View all HP Xw8400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

4. Attach a data cable from a SATA connector on the system board to the hard drive, and attach the fifth drive power cable to the drive. Figure 4-61 Attaching the data cable for the SATA hard drive in the fifth hard drive bay 5. For a SAS hard drive, attach a SAS/SATA adapter to the connector on the hard drive. Attach a data cable from a SAS connector on the system board to the hard drive, and attach a power cable to the drive. Processor heatsink Removing the CPU heatsink NOTE: The following illustrated CPU heatsink is typical of what you might have in your workstation. Be aware that different variations of the CPU heatsinks exist, but the overall procedures listed are sufficient to assist you in removing the CPU heatsink. 1. Shut down the workstation, and disconnect power from the system ( Pre-disassembly procedures on page 50). Remove the access panel (Access panel on page 57), and place the workstation on its side with the system board facing up. ENWW Removing and replacing components 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
4.
Attach a data cable from a SATA connector on the system board to the hard drive, and attach the
fifth drive power cable to the drive.
Figure 4-61
Attaching the data cable for the SATA hard drive in the fifth hard drive bay
5.
For a SAS hard drive, attach a SAS/SATA adapter to the connector on the hard drive. Attach a
data cable from a SAS connector on the system board to the hard drive, and attach a power cable
to the drive.
Processor heatsink
Removing the CPU heatsink
NOTE:
The following illustrated CPU heatsink is typical of what you might have in your workstation.
Be aware that different variations of the CPU heatsinks exist, but the overall procedures listed are
sufficient to assist you in removing the CPU heatsink.
1.
Shut down the workstation, and disconnect power from the system (
Pre-disassembly
procedures
on page
50
). Remove the access panel (
Access panel
on page
57
), and place the
workstation on its side with the system board facing up.
ENWW
Removing and replacing components
93