HP Xw8400 HP xw8400 Workstation - Service and Technical Reference Guide - Page 69

Bezel blanks, Hood sensor (Smart Cover Sensor),

Get HP Xw8400 - Workstation - 4 GB RAM PDF manuals and user guides
UPC - 883585271085
View all HP Xw8400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Bezel blanks To remove the bezel blanks: 1. Disconnect power from the system ( Pre-disassembly procedures on page 50) and remove the front bezel (Front bezel on page 58) 2. Remove the bezel blanks by squeezing in on the tabs (1) and pushing the bezel blanks out (2). Figure 4-9 Removing the bezel blanks Hood sensor (Smart Cover Sensor) To remove the hood sensor: 1. Disconnect power from the system ( Pre-disassembly procedures on page 50) and remove the access panel (Access panel on page 57). Lay the workstation on its side with the system board facing up. 2. Disconnect the white 1 x 3 hood sensor connector from the inline connector attached to the front panel harness. ENWW Removing and replacing components 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
Bezel blanks
To remove the bezel blanks:
1.
Disconnect power from the system (
Pre-disassembly procedures
on page
50
) and remove the
front bezel (
Front bezel
on page
58
)
2.
Remove the bezel blanks by squeezing in on the tabs
(1)
and pushing the bezel blanks out
(2)
.
Figure 4-9
Removing the bezel blanks
Hood sensor (Smart Cover Sensor)
To remove the hood sensor:
1.
Disconnect power from the system (
Pre-disassembly procedures
on page
50
) and remove the
access panel (
Access panel
on page
57
). Lay the workstation on its side with the system board
facing up.
2.
Disconnect the white 1 x 3 hood sensor connector from the inline connector attached to the front
panel harness.
ENWW
Removing and replacing components
59