HP Xw8400 HP xw8400 Workstation - Service and Technical Reference Guide - Page 95

CAUTION, drive is partially inserted, release the drivelock release lever

Get HP Xw8400 - Workstation - 4 GB RAM PDF manuals and user guides
UPC - 883585271085
View all HP Xw8400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

2. Disconnect the data (1), power (2) and audio (3) cables from the drive. The connector colors might be different than illustrated. NOTE: The audio cable is only required for Linux-based systems. Figure 4-47 Disconnecting the IDE (left) or SATA (right) cable from the optical drive 3. Lift the green drivelock release lever, and gently slide the drive out of the chassis. Figure 4-48 Removing the optical drive from the chassis To replace an optical drive: 1. Lift the green drivelock release lever while sliding the optical drive into the bay. When the optical drive is partially inserted, release the drivelock release lever, and slide the drive completely into the bay until the drive is secured. CAUTION: Ensure that the optical drive is secure. Failure to do so can cause damage to the drive when moving the workstation. 2. Connect the power, data , and audio (if required) cables to the drive and workstation. NOTE: The audio cable is only required for Linux-based systems. ENWW Removing and replacing components 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
2.
Disconnect the data
(1)
, power
(2)
and audio
(3)
cables from the drive. The connector colors might
be different than illustrated.
NOTE:
The audio cable is only required for Linux-based systems.
Figure 4-47
Disconnecting the IDE (left) or SATA (right) cable from the optical drive
3.
Lift the green drivelock release lever, and gently slide the drive out of the chassis.
Figure 4-48
Removing the optical drive from the chassis
To replace an optical drive:
1.
Lift the green drivelock release lever while sliding the optical drive into the bay. When the optical
drive is partially inserted, release the drivelock release lever, and slide the drive completely into
the bay until the drive is secured.
CAUTION:
Ensure that the optical drive is secure. Failure to do so can cause damage to the drive
when moving the workstation.
2.
Connect the power, data , and audio (if required) cables to the drive and workstation.
NOTE:
The audio cable is only required for Linux-based systems.
ENWW
Removing and replacing components
85