Icom F3400D / F4400D Operation Guide - Page 171

Copying data from a transceiver, ◇ Connecting, ◇ Copying data

Get Icom F3400D / F4400D PDF manuals and user guides View all Icom F3400D / F4400D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 171 highlights

Previous view 13 OTHERS Copying data from a transceiver This section describes how to copy data from a Master transceiver to a Sub transceiver using the optional OPC-1870 or OPC-2362 zone copy cable. The copying procedure differs, depending on the type of the Master transceiver used. NOTE: Before copying, the "Transceiver Data Out" item must be set to "ON" using the programming software. DDConnecting Before copying, the Master and Sub transceivers should be connected using the optional OPC-1870 or OPC-2362 zone copy cable. 1. Turn OFF the Master and Sub transceivers. 2. Connect the two transceivers with the cable. The following cables are used: ••OPC-1870: Used between a Portable and a Portable. ••OPC-2362: Used between a Portable and a Mobile. Portable and Portable connection Turn OFF OPC-1870 DDCopying data Master: Portable Ten-key or Simple key types Mobile LCD types Step 1: Entering the Programming mode (Master) 1. While holding down [P1] and [Down], turn ON the transceiver. Continue holding down [P1] and [Down] for about 3 seconds. ••2 beeps sound. 2. P ush [Up] or [Down] to select "Programming." ••The transceiver enters the Programming mode. Step 2: Turning ON the transceiver (Sub) Step 3: Copying data (Master) Push the [PTT] (Portable) or Power switch (Mobile) to start copying data to the Sub transceiver. Step 4: Complete (Master/Sub) After copying is completed, the Master and Sub transceivers automatically restart. ••The user can operate the Sub transceiver with the loaded data. Turn OFF Portable and Mobile connection Turn OFF OPC-2362 Turn OFF 13-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
13
OTHERS
13-4
Copying data from a transceiver
This section describes how to copy data from a
Master transceiver to a Sub transceiver using the
optional OPC-1870 or OPC-2362
ZONE
COPY
CABLE
.
The copying procedure differs, depending on the type
of the Master transceiver used.
NOTE:
Before copying, the “Transceiver Data Out”
item must be set to “ON” using the programming
software.
D
Copying data
Master: Portable Ten-key or Simple key types
Mobile LCD types
Step 1: Entering the Programming mode
(Master)
1.
While holding down [P1] and [Down], turn ON
the transceiver. Continue holding down [P1] and
[Down] for about 3 seconds.
•
2 beeps sound.
2.
Push [Up] or [Down] to select “Programming.”
•
The transceiver enters the Programming mode.
Step 2: Turning ON the transceiver
(Sub)
Step 3: Copying data
(Master)
Push the [PTT] (Portable) or Power switch (Mobile) to
start copying data to the Sub transceiver.
Step 4: Complete
(Master/Sub)
After copying is completed, the Master and Sub
transceivers automatically restart.
•
The user can operate the Sub transceiver with the loaded
data.
D
Connecting
Before copying, the Master and Sub transceivers
should be connected using the optional OPC-1870 or
OPC-2362
ZONE
COPY
CABLE
.
1.
Turn OFF the Master and Sub transceivers.
2.
Connect the two transceivers with the cable.
The following cables are used:
•
OPC-1870:
Used between a Portable and a
Portable.
•
OPC-2362:
Used between a Portable and a
Mobile.
Portable and Portable connection
Portable and Mobile connection
OPC-1870
Turn OFF
Turn OFF
Turn OFF
Turn OFF
OPC-2362