Icom F3400D / F4400D Operation Guide - Page 24
Scan Add/Del Tag, High/Low, C.Tone CH Select, Tone/RAN CH Select, Monitor, Talk Around, Bandwidth
View all Icom F3400D / F4400D manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 24 highlights
Previous view 2 PANEL DESCRIPTION Assignable Software key functions DDFor keys and keypads Category: Channel/Scan (Voting) (Continued) Scan Add/Del (Tag) zzPush to add a channel to, or delete it from the current Scan list. ••When a channel is added to the current Scan list, the current Scan list text and "ON" are briefly displayed. ••When a channel is deleted from the current Scan list, the current Scan list text and "OFF" are briefly displayed. zzYou can add a channel to, or delete it from a selected Scan list. 1. Hold down for 1 second to display the "Scan Tag" screen. 2. Push [Up] or [Down] to select a list. 3. Push [OK] to add a channel to, or delete it from the selected list. ••When a channel is added to the selected Scan list, the current Scan list text and "ON" are briefly displayed. ••When a channel is deleted from the selected Scan list, the current Scan list text and "OFF" are briefly displayed. 4. P ush [Back] to exit the "Scan Tag" screen. zzWhile a Scan is paused by detecting a signal on a channel (except for primary or secondary channel), push this key to remove the channel from the Scan list. TIP: When the Nuisance Delete function is ON, the removed channel is automatically added to the Scan list again, after the Scan is canceled. High/Low Push to select the transmit output power level temporarily or permanently, depending on the presetting. C.Tone CH Select In the Analog mode Push to display the "C.Tone CH Select" screen. Then push [Up] or [Down] to select a tone frequency or code. After selecting, push [OK] to save. Tone/RAN CH Select In the Analog mode Push to display the "C.Tone CH Select" screen. Then push [Up] or [Down] to select a tone frequency or code. After selecting, push [OK] to save. In the Digital mode Push to display the "RAN CH Select" screen. Then push [Up] or [Down] to select a RAN code. After selecting, push [OK] to save. Monitor zzPush to turn the CTCSS (DTCS), 2-Tone, or 5-Tone squelch mute ON or OFF. LOnly during 2-Tone mode operation, push to open any squelch, or deactivate any mute functions. LOnly during 5-Tone mode operation, push to activate one or two of the following functions on each channel (Depending on the presetting): - Hold down to unmute the channel (Audible mode). - Push to mute the channel (Inaudible mode). NOTE: The audible (unmute) mode may automatically return to the Inaudible (mute) mode, after the preset time period. zzDepending on the presetting, holding down this key for 1 second may cancel the Scan. Talk Around Push to turn the Talk Around function ON or OFF. LThe Talk Around function equalizes the transmit frequency to the receive frequency, for direct (Simplex) communication. Bandwidth In the Analog mode Push to temporarily set the channel width to Wide* or Narrow. LThe wide passband width can be preset to either 25.0 kHz (Wide) or 20.0 kHz (Mid). Depending on the presetting, Mid channel width may be selectable. *The Wide channel width is not usable for the USA version transceivers. Scrambler/Encryption In the Analog mode Push to turn the Voice Scrambler function ON or OFF. LThe Voice Scrambler function provides private communication between stations by using a scrambled code. In the Digital mode Push to turn the Encryption function ON or OFF. LThe Voice or Data Encryption function provides private communication between stations by using an Encryption Key and Key ID. Compander In the Analog mode Push to turn the Compander function ON or OFF. LThe Compander function reduces noise components on the transmit audio to provide clear communication. 2-16