Icom F3400D / F4400D Operation Guide - Page 78

<Key operation&gt, Portable, Mobile, Using [Status], Push [Up] or [Down] to select a Status Message

Get Icom F3400D / F4400D PDF manuals and user guides View all Icom F3400D / F4400D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Previous view 7 NXDN™ OPERATION Transmitting a call DDTransmitting a Status message (Continued) Portable: For the Ten-key and the Simple key types Mobile: For the LCD types Using [Status]: 1. Push [Status] to display the "Status" screen. 2. P ush [Up] or [Down] to select a Status Message, then push [PTT] to transmit it. L"Success" is displayed after receiving an acknowledgement from the target station. L"Failed" is displayed if the target station does not send back an acknowledgement. Portable: For the Non-display types Mobile: For the Segment types Using [Status]: Hold down [Status] for 1 second transmit the preset Status Message. TIP: This operation is enabled only when [Selector]'s operation is set to "Status" using the programming software. NOTE: The status message can be automatically transmitted when: ••The transceiver is turned ON or OFF LSet the Status message to be transmitted in 'Power ON Status' or 'Power OFF Status' item, respectively. LSet the target station ID in 'Power Status ID,' 'Power Status ID for Single-site Trunk' or 'Power Status ID for Multi-site Trunk.' • After sending a voice message LSet the 'Send with Voice Call' item to 'Enable.' LSet the Status message to be transmitted in 'Send Status Number' item. 7-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
7
NXDN™ OPERATION
7-6
Transmitting a call
D
Transmitting a Status message (Continued)
<Key operation>
Portable:
For the Ten-key and the Simple key types
Mobile:
For the LCD types
Using [Status]:
1.
Push [Status] to display the “Status” screen.
2.
Push [Up] or [Down] to select a Status Message,
then push [PTT] to transmit it.
L
“Success” is displayed after receiving an
acknowledgement from the target station.
L
“Failed” is displayed if the target station does not
send back an acknowledgement.
Portable:
For the Non-display types
Mobile:
For the Segment types
Using [Status]:
Hold down [Status] for 1 second transmit the preset
Status Message.
TIP:
This operation is enabled only when [Selector]’s
operation is set to “Status” using the programming
software.
NOTE:
The status message can be automatically
transmitted when:
• The transceiver is turned ON or OFF
L
Set the Status message to be transmitted in ‘Power ON
Status’ or ‘Power OFF Status’ item, respectively.
L
Set the target station ID in ‘Power Status ID,’ ‘Power
Status ID for Single-site Trunk’ or ‘Power Status ID for
Multi-site Trunk.’
• After sending a voice message
L
Set the ‘Send with Voice Call’ item to ‘Enable.’
L
Set the Status message to be transmitted in ‘Send
Status Number’ item.