Home » Icom Manuals » Two-Way Radios » Icom IC-7200 » Manual Viewer

Icom IC-7200 Instruction Manual - Page 12

■ Function display, MEMORY CHANNEL NUMBER READOUT - data mode

Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

1 PANEL DESCRIPTION ■ Function display q w e r t !4 y !3 u i !2 !1 !0 o q TRANSMIT INDICATOR Appears while transmitting. w MODE INDICATORS Shows the selected operating mode. • " " appears when SSB/AM data mode is selected. (p. 71) • "-R" appears when CW reverse or RTTY reverse mode is selected. (pgs. 29, 35, 39) e IF FILTER INDICATORS (p. 47) Shows the selected IF filter. ➥ " " appears when the wide IF filter is selected. ➥ " " appears when the normal IF filter is selected. ➥ " " appears when the narrow IF filter is selected. r LOCK INDICATOR (p. 29) Appears when the dial lock function is activated. t MEMORY INDICATOR (p. 61) Appears when memory mode is selected. y M EMORY CHANNEL NUMBER READOUT (p. 61) Shows the selected memory channel number. u BLANK INDICATOR (p. 62) Appears when the selected memory channel is blank. • This indicator appears both in VFO and memory mode. i S/RF METER ➥ Shows receiving signal strength while receiving. ➥ Shows either transmit power meter (PO), SWR or ALC while transmitting. (p. 30) o NOTCH INDICATORS (p. 51) ➥ " " appears when the automatic notch function is activated. ➥ " " appears when the manual notch function is activated. !0 NOISE REDUCTION INDICATOR (p. 50) Appears when the noise reduction is activated. !1 NOISE BLANKER INDICATOR (p. 49) Appears when the noise blanker is activated. !2 TUNE INDICATOR (p. 67) ➥ Appears when the optional automatic antenna tuner is activated. ➥ Blinks while tuning. !3 RECEIVE INDICATOR Appears while receiving a signal or when the squelch is open. !4 FREQUENCY READOUT Shows the operating frequency.

Section	Page
Front cover	1
IMPORTANT	2
FOREWORD	2
EXPLICIT DEFINITIONS	2
SUPPLIED ACCESSORIES	2
FCC INFORMATION	2
PRECAUTIONS	3
TABLE OF CONTENTS	4
1 PANEL DESCRIPTION	6
■ Front panel	6
◇ Keypad	10
■ Function display	12
■ Rear panel	14
◇ ACC socket information	15
■ Microphones	16
◇ HM-36	16
◇ SM-20(Option)	16
2 INSTALLATION AND CONNECTIONS	17
■ Unpacking	17
■ Selecting a location	17
■ Grounding	17
■ Antenna connection	17
■ Required connections	18
■ Advanced connections	19
■ Power supply connections	20
■ Connecting the DC Power Supply	20
■ Battery connections	20
■ External antenna tuners	21
■ Linear amplifier connections	22
■ Connections for CW	23
■ Connections for RTTY	24
◇ Connections for RTTY (FSK)	24
◇ Connections for RTTY (AFSK)	24
■ Connections for SSTV or PSK31	25
◇ When connecting to the [ACC] socket	25
◇ When connecting to the [MIC] connector	25
◇ When connecting to the [USB] jack	25
3 BASIC OPERATION	26
■ Before first applying power	26
■ Applying power (CPU resetting)	26
■ VFO description	27
■ VFO operation	27
◇ Selecting the VFO A/B	27
◇ VFO equalization	27
■ Selecting VFO/memory mode	28
◇ Differences between VFO mode and memory mode	28
■ Selecting an operating band	29
◇ Using the band stacking register	29
■ Frequency setting	30
◇ Using the main dial	30
◇ Direct frequency entry with keypad	30
◇ Programmable tuning steps	31
◇ Selecting the programmable tuning step	31
◇ 1 Hz and 10 Hz tuning steps	32
◇ TS switch flow chart	32
◇ Auto tuning step function	33
◇ ¼ tuning function (SSB data/CW/RTTY only)	33
◇ Band edge warning beep	33
■ Volume setting	34
■ Operating mode selection	34
■ Dial lock function	34
■ RF gain and Squelch	35
■ Meter function	35
■ Basic transmit operation	36
◇ Transmitting	36
◇ Output power and Microphone gain settings	36
■ Voice synthesizer function	37
4 RECEIVE AND TRANSMIT	38
■ Operating SSB	38
◇ Convenient functions for receive	38
◇ Convenient functions for transmit	39
◇ About 5 MHz band operation (USA version only)	39
■ Operating CW	40
◇ Convenient functions for receive	41
◇ Convenient functions for transmit	41
◇ CW reverse mode	42
◇ CW pitch control	42
◇ CW side tone function	43
◇ Keying speed setting	43
■ Operating RTTY (FSK)	44
◇ Convenient functions for receive	44
◇ RTTY reverse mode	45
◇ Twin peak filter	45
◇ RTTY decode set mode	46
■ Operating AM	47
◇ Convenient functions for receive	47
◇ Convenient functions for transmit	47
■ Data mode (SSTV/PSK31) operation	48
5 FUNCTIONS FOR RECEIVE	49
■ RIT function	49
■ Preamp and attenuator	50
■ AGC function	50
◇ AGC time constant selection	50
■ Twin PBT operation	51
■ IF filter selection	52
◇ IF filter selection	52
◇ Filter passband width setting	53
◇ IF filter shape (SSB/CW only)	53
■ Noise blanker	54
◇ Noise blanker settings	54
■ Noise reduction	55
◇ Noise reduction level setting	55
■ Notch function	56
◇ Auto notch function	56
◇ Manual notch function	56
◇ Manual notch filter setting	57
6 FUNCTIONS FOR TRANSMIT	58
■ VOX function	58
◇ Adjusting the VOX function	58
◇ VOX set mode	59
■ Break-in function	60
◇ Semi break-in operation	60
◇ Full break-in operation	61
■ Speech compressor	62
◇ Compression level setting	62
■ Split frequency operation	63
◇ Quick split function	64
◇ Split lock function	64
■ Measuring SWR	65
7 MEMORY OPERATION	66
■ Memory channels	66
■ Memory channel selection	66
■ Memory programming	67
◇ Programming in VFO mode	67
◇ Programming in memory mode	67
■ Frequency copying	68
◇ Copying in memory mode	68
■ Memory clearing	69
8 SCAN OPERATION	70
■ Scan types	70
■ Preparation	70
■ Programmed scan operation (VFO mode)	71
■ Memory scan operation (Memory mode)	71
9 ANTENNA TUNER OPERATION	72
■ Optional AT-180 automatic antenna tuner operation	72
◇ Tuner operation	72
◇ Manual tuning	72
■ AT-180 internal switch description	73
■ Optional AH-4 automatic antenna tuner operation	74
◇ AH-4 operation	74
10 SET MODE	75
■ General	75
◇ Quick set mode operation	75
◇ Set mode operation	75
■ Quick set mode	76
■ Set mode	79
◇ Paddle operation from [MIC] connector	87
11 MAINTENANCE	88
■ Fuse replacement	88
◇ DC power cable fuse replacement	88
◇ Circuitry fuse replacement	88
■ Memory backup	89
■ Resetting the CPU	89
■ Cleaning	89
12 TROUBLESHOOTING	90
13 OPTION INSTALLATIONS	92
■ MB-116 HANDLES installation	92
■ MB-117 CARRYING HANDLE installation	92
■ MB-118 MOBILE MOUNTING BRACKET installation	92
14 CONTROL COMMAND	93
■ Remote jack (CI-V) information	93
◇ CI-V connection example	93
◇ Data format	93
◇ Command table	94
◇ Band stacking register	96
◇ Data mode with filter width setting	96
15 SPECIFICATIONS	97
■ General	97
■ Transmitter	97
■ Receiver	97
16 OPTIONS	98
17 ABOUT CE	100
18 BAND VOLTAGE MODIFICATION	102
■ Band voltage modification	102