Icom IC-7200 Instruction Manual - Page 33

3 BASIC OPERATION D Auto tuning step function When rotating the tuning dial rapidly, the tuning speed accelerates automatically as selected. MODE TS TUNER FILTER SPCH NB NR ANF METER V/M 1 1.8 A=/B 2 3.5 SPLIT 3 7 MW 4 10 M-CL 5 14 AGC 6 18 COMP271 RIT . GENE SCAN 8 24 MNF 0 50 VOX 9 28 F-INP ENT BAND P.AMP ATT M-CH/RIT SET [DIAL] [M-CH] q Push and hold M-CH/RIT SET for 1 sec. twice to enter the set mode. w Rotate [M-CH] to select "AUTo TS." e Rotate [DIAL] to select the desired tuning speed from HI (High), Lo (Low) and oF (OFF). • HI : Approx. 5 times faster when the tuning step is set to 1 kHz or smaller steps; approx. 2 times faster when the tuning step is set to 5 kHz or larger steps. • Lo : Approx. 2 times faster • oF : Auto tuning step is turned OFF • Push and hold M-CL for 1 sec. to select a default con- dition or value. When "HI" is selected (default) r Push M-CH/RIT SET to exit the set mode and return to normal operation. D ¼ tuning function (SSB data/CW/RTTY only) While operating in SSB data/CW/RTTY, the ¼ tuning function is available for critical tuning. Dial sensitivity is reduced to ¼ of normal when the ¼ function is in use. MODE TS TUNER FILTER SPCH NB NR ANF METER V/M 1 1.8 A=/B 2 3.5 SPLIT 3 7 MW 4 10 M-CL 5 14 AGC 6 18 COMP271 RIT . GENE SCAN 8 24 MNF 0 50 VOX 9 28 F-INP ENT BAND P.AMP ATT M-CH/RIT SET q Push and hold M-CH/RIT SET for 1 sec. twice to enter the set mode. w Rotate [M-CH] to select "DIAL ¼." e Rotate [DIAL] to select the ¼ tuning function ON and OFF. • Push and hold M-CL for 1 sec. to select a default con- dition or value. When "OFF" is selected (default) [DIAL] [M-CH] r Push M-CH/RIT SET to exit the set mode and return to normal operation. NOTE: This function is only available when the programmable tuning step is OFF (p. 26). D Band edge warning beep When selecting a frequency that lies outside of a band's specified frequency range, a warning beep sounds. This function can be turned OFF in set mode, if desired. MODE TS TUNER FILTER SPCH NB NR ANF METER V/M 1 1.8 A=/B 2 3.5 SPLIT 3 7 MW 4 10 M-CL 5 14 AGC 6 18 COMP271 RIT . GENE SCAN 8 24 MNF 0 50 VOX 9 28 F-INP ENT BAND P.AMP ATT M-CH/RIT SET [DIAL] [M-CH] q Push and hold M-CH/RIT SET for 1 sec. twice to enter the set mode. w Rotate [M-CH] to select "BAND BEP." e Rotate [DIAL] to select the band edge warning beep function ON and OFF. • Push and hold M-CL for 1 sec. to select a default con- dition or value. When "ON" is selected (default) r Push M-CH/RIT SET to exit the set mode and return to normal operation. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 28