Home » Icom Manuals » Two-Way Radios » Icom IC-7200 » Manual Viewer

Icom IC-7200 Instruction Manual - Page 32

◇ 1 Hz and 10 Hz tuning steps, ◇ TS switch flow chart

Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

3 BASIC OPERATION D 1 Hz and 10 Hz tuning steps When the programmable tuning step "Z" disappears, rotating [DIAL] changes the frequency in increments of 1 or 10 Hz. NOTE: The frequency is changed in 50 Hz step when the [UP]/[DN] switches of the microphone are used for the frequency setting (when the programmable tuning step is not selected; "Z" disappears.) MODE TS TUNER FILTER SPCH NB NR ANF METER V/M 1 1.8 A=/B 2 3.5 SPLIT 3 7 MW 4 10 M-CL 5 14 AGC 6 18 COMP271 RIT . GENE SCAN 8 24 MNF 0 50 VOX 9 28 F-INP ENT BAND P.AMP ATT M-CH/RIT SET [DIAL] ➥ Push and hold TS for 1 sec. to toggle between the 1 Hz and 10 Hz step settings. • When the 1 Hz step is selected, the 1 Hz digit appears in the frequency indication; when the 10 Hz step is selected, the 1 Hz digit disappears from the frequency indication. • Rotating [DIAL] changes the frequency in 1 Hz or 10Hz tuning step. 10 Hz tuning Rotating [DIAL] changes the frequency in 10 Hz steps. 1 Hz tuning Push and hold TS for 1 sec. D TS switch flow chart Appears Rotating [DIAL] changes the frequency in 1 Hz steps. Programmable tuning step indicator 10 Hz tuning 1 sec. Push and hold 1 sec. Push TS momentarily Programmable step tuning (0.1 kHz -10 kHz) 1 sec. Push momentarily Appears 1 Hz tuning Tuning step set mode 27

Section	Page
Front cover	1
IMPORTANT	2
FOREWORD	2
EXPLICIT DEFINITIONS	2
SUPPLIED ACCESSORIES	2
FCC INFORMATION	2
PRECAUTIONS	3
TABLE OF CONTENTS	4
1 PANEL DESCRIPTION	6
■ Front panel	6
◇ Keypad	10
■ Function display	12
■ Rear panel	14
◇ ACC socket information	15
■ Microphones	16
◇ HM-36	16
◇ SM-20(Option)	16
2 INSTALLATION AND CONNECTIONS	17
■ Unpacking	17
■ Selecting a location	17
■ Grounding	17
■ Antenna connection	17
■ Required connections	18
■ Advanced connections	19
■ Power supply connections	20
■ Connecting the DC Power Supply	20
■ Battery connections	20
■ External antenna tuners	21
■ Linear amplifier connections	22
■ Connections for CW	23
■ Connections for RTTY	24
◇ Connections for RTTY (FSK)	24
◇ Connections for RTTY (AFSK)	24
■ Connections for SSTV or PSK31	25
◇ When connecting to the [ACC] socket	25
◇ When connecting to the [MIC] connector	25
◇ When connecting to the [USB] jack	25
3 BASIC OPERATION	26
■ Before first applying power	26
■ Applying power (CPU resetting)	26
■ VFO description	27
■ VFO operation	27
◇ Selecting the VFO A/B	27
◇ VFO equalization	27
■ Selecting VFO/memory mode	28
◇ Differences between VFO mode and memory mode	28
■ Selecting an operating band	29
◇ Using the band stacking register	29
■ Frequency setting	30
◇ Using the main dial	30
◇ Direct frequency entry with keypad	30
◇ Programmable tuning steps	31
◇ Selecting the programmable tuning step	31
◇ 1 Hz and 10 Hz tuning steps	32
◇ TS switch flow chart	32
◇ Auto tuning step function	33
◇ ¼ tuning function (SSB data/CW/RTTY only)	33
◇ Band edge warning beep	33
■ Volume setting	34
■ Operating mode selection	34
■ Dial lock function	34
■ RF gain and Squelch	35
■ Meter function	35
■ Basic transmit operation	36
◇ Transmitting	36
◇ Output power and Microphone gain settings	36
■ Voice synthesizer function	37
4 RECEIVE AND TRANSMIT	38
■ Operating SSB	38
◇ Convenient functions for receive	38
◇ Convenient functions for transmit	39
◇ About 5 MHz band operation (USA version only)	39
■ Operating CW	40
◇ Convenient functions for receive	41
◇ Convenient functions for transmit	41
◇ CW reverse mode	42
◇ CW pitch control	42
◇ CW side tone function	43
◇ Keying speed setting	43
■ Operating RTTY (FSK)	44
◇ Convenient functions for receive	44
◇ RTTY reverse mode	45
◇ Twin peak filter	45
◇ RTTY decode set mode	46
■ Operating AM	47
◇ Convenient functions for receive	47
◇ Convenient functions for transmit	47
■ Data mode (SSTV/PSK31) operation	48
5 FUNCTIONS FOR RECEIVE	49
■ RIT function	49
■ Preamp and attenuator	50
■ AGC function	50
◇ AGC time constant selection	50
■ Twin PBT operation	51
■ IF filter selection	52
◇ IF filter selection	52
◇ Filter passband width setting	53
◇ IF filter shape (SSB/CW only)	53
■ Noise blanker	54
◇ Noise blanker settings	54
■ Noise reduction	55
◇ Noise reduction level setting	55
■ Notch function	56
◇ Auto notch function	56
◇ Manual notch function	56
◇ Manual notch filter setting	57
6 FUNCTIONS FOR TRANSMIT	58
■ VOX function	58
◇ Adjusting the VOX function	58
◇ VOX set mode	59
■ Break-in function	60
◇ Semi break-in operation	60
◇ Full break-in operation	61
■ Speech compressor	62
◇ Compression level setting	62
■ Split frequency operation	63
◇ Quick split function	64
◇ Split lock function	64
■ Measuring SWR	65
7 MEMORY OPERATION	66
■ Memory channels	66
■ Memory channel selection	66
■ Memory programming	67
◇ Programming in VFO mode	67
◇ Programming in memory mode	67
■ Frequency copying	68
◇ Copying in memory mode	68
■ Memory clearing	69
8 SCAN OPERATION	70
■ Scan types	70
■ Preparation	70
■ Programmed scan operation (VFO mode)	71
■ Memory scan operation (Memory mode)	71
9 ANTENNA TUNER OPERATION	72
■ Optional AT-180 automatic antenna tuner operation	72
◇ Tuner operation	72
◇ Manual tuning	72
■ AT-180 internal switch description	73
■ Optional AH-4 automatic antenna tuner operation	74
◇ AH-4 operation	74
10 SET MODE	75
■ General	75
◇ Quick set mode operation	75
◇ Set mode operation	75
■ Quick set mode	76
■ Set mode	79
◇ Paddle operation from [MIC] connector	87
11 MAINTENANCE	88
■ Fuse replacement	88
◇ DC power cable fuse replacement	88
◇ Circuitry fuse replacement	88
■ Memory backup	89
■ Resetting the CPU	89
■ Cleaning	89
12 TROUBLESHOOTING	90
13 OPTION INSTALLATIONS	92
■ MB-116 HANDLES installation	92
■ MB-117 CARRYING HANDLE installation	92
■ MB-118 MOBILE MOUNTING BRACKET installation	92
14 CONTROL COMMAND	93
■ Remote jack (CI-V) information	93
◇ CI-V connection example	93
◇ Data format	93
◇ Command table	94
◇ Band stacking register	96
◇ Data mode with filter width setting	96
15 SPECIFICATIONS	97
■ General	97
■ Transmitter	97
■ Receiver	97
16 OPTIONS	98
17 ABOUT CE	100
18 BAND VOLTAGE MODIFICATION	102
■ Band voltage modification	102