Icom IC-7200 Instruction Manual - Page 87

◇ Paddle operation from [MIC] connector, CT-17 CI-V LEVEL CONVERTER, rotate [DIAL] to select - hf transceiver

Get Icom IC-7200 PDF manuals and user guides View all Icom IC-7200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

SET MODE 10 Mode Select (AM) This item inhibits the selection of AM mode, and allows you to simplify operation. on : AM modes are selectable. oF : AM modes are inhibited. CI-V Baud Rate Sets the CI-V data transfer rate. 300, 1200, 4800, 9600, 19200 bps and Auto are available. When Auto is selected, the baud rate is automatically set according to the connected controller or remote controller. ON (default) Auto (default) CI-V Address To distinguish equipment, each CI-V transceiver has its own Icom standard address in hexadecimal code. The IC-7200's address is 76h. When 2 or more IC-7200s are connected to an optional CT-17 CI-V LEVEL CONVERTER, rotate [DIAL] to select a different address for each IC-7200 in the range 01h to 7Fh. 76 : Address of 76h 76h (default) CI-V Transceive Transceive operation is possible with the IC-7200 connected to other Icom HF transceivers or receivers. When "ON" is selected, changing the frequency, operating mode, etc. on the IC-7200 automatically changes those of connected transceivers (or receivers) and vice versa. on : Transceive ON oF : Transceive OFF ON (default) Reference Frequency Adjustment Adjusts the internal reference signal frequency within 0% to 100% range in 1% steps during frequency calibration. NOTE: Default setting is different for each transceiver. D Paddle operation from [MIC] connector Connect a CW paddle as at right to operate an electronic keyer from the [mic] connector. • Be sure to select "Paddle Polarity," "Keyer Type" and "Mic Up/Down Keyer" in the set mode. (pgs. 80, 81) • Connect straight key to "Dot" side. • Push both of "Dot" and "DASH" to activate the squeeze operation. CW paddle DOT DASH 3.9 kø ±5% GND y MIC U/D e 2.2 kø ±5% MIC connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Mode Select (AM)
This item inhibits the selection of AM mode, and allows
you to simplify operation.
on : AM modes are selectable.
oF : AM modes are inhibited.
ON (default)
CI-V Baud Rate
Sets the CI-V data transfer rate. 300, 1200, 4800, 9600,
19200 bps and Auto are available.
When Auto is selected, the baud rate is automatically set
according to the connected controller or remote controller.
Auto (default)
CI-V Address
To distinguish equipment, each CI-V transceiver has its
own Icom standard address in hexadecimal code.
The IC-7200’s address is 76h.
When 2 or more IC-7200s are connected to an optional
CT-17 CI-V LEVEL CONVERTER, rotate [DIAL] to select
a different address for each IC-7200 in the range 01h to
7Fh.
76 : Address of 76h
76h (default)
CI-V Transceive
Transceive operation is possible with the IC-7200 con-
nected to other Icom HF transceivers or receivers.
When “ON” is selected, changing the frequency, operat-
ing mode, etc. on the IC-7200 automatically changes
those of connected transceivers (or receivers) and vice
versa.
on : Transceive ON
oF : Transceive OFF
ON (default)
Reference Frequency Adjustment
Adjusts the internal reference signal frequency within 0%
to 100% range in 1% steps during frequency calibration.
NOTE:
Default setting is different for each transceiver.
D
Paddle operation from [MIC] connector
Connect a CW paddle as at right to operate an elec-
tronic keyer from the [MIC] connector.
• Be sure to select “Paddle Polarity,” “Keyer Type” and
“Mic Up/Down Keyer” in the set mode. (pgs. 80, 81)
• Connect straight key to “DOT” side.
• Push both of “DOT” and “DASH” to activate the
squeeze operation.
MIC connector
CW
paddle
DOT
DASH
3.9 k
ø
±5%
2.2 k
ø
±5%
MIC U/D
e
GND
y
82
10
SET MODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21