Icom IC-7200 Instruction Manual - Page 94

14 CONTROL COMMAND D Command table Command Sub command Description 00 - Send frequency data. (for transceive operation) 01 00 Select LSB mode (for transceive operation) 01 Select USB mode (for transceive operation) 02 Select AM mode (for transceive operation) 03 Select CW mode (for transceive operation) 04 Select RTTY mode (for transceive operation) 07 Select CW-R mode (for transceive operation) 08 Select RTTY-R mode (for transceive operation) 02 - Read band edge frequencies 03 - Read operating frequency 04 - Read operating mode 05 - Set operating frequency 06 07 00 Select LSB mode 01 Select USB mode 02 Select AM mode 03 Select CW mode 04 Select RTTY mode 07 Select CW-R mode 08 Select RTTY-R mode - Select VFO mode 00 Select VFO A 01 Select VFO B A0 Equalize VFO A and VFO B B0 Exchange VFO A and VFO B 08 - Select memory mode 0001−0201* Select memory channel *P1=0200, P2=0201 09 - Memory write 0A - Memory to VFO 0B - Memory clear 0E 00 Scan stop 01 Programmed/memory scan start 02 Programmed scan start 22 Memory scan start D0 Set scan resume OFF D3 Set scan resume ON 0F 00 Turn the split function OFF 01 Turn the split function ON 10 00 Select 10 Hz (or 1 Hz) tuning step 01 Select 100 Hz tuning step 02 Select 1 kHz tuning step 03 Select 5 kHz tuning step 04 Select 9 kHz tuning step 05 Select 10 kHz tuning step 11 - Set/read attenuator. (0=OFF, 20=ON (20 dB)) 13 00 Announce with voice synthesizer 01 (00=all data 01=frequency and 02 S-meter; 02=receive mode) 89 Command Sub command Description 14 01 [AF] level setting (0=max. CCW to 255=max. CW) 02 [RF] level setting (0=max. CCW to 255=11 o'clock) 03 [SQL] level setting (0=11 o'clock to 255=max. CW) 06 NR level setting (0=0% to 255=100%) 07 Inside [PBT] setting (0= max. CCW, 128=center, 255=max. CW) 08 Outside [PBT] setting (0= max. CCW, 128=center, 255=max. CW) 09 CW Pitch setting (0=300 Hz to 255=900 Hz (5 Hz steps)) 0A RF power setting (0=minimum to 255=100%) 0B MIC gain setting (0=0% to 255=100%) 0C Key speed level setting (0=6 wpm to 255=60 wpm) 0D [MNF] setting (0=max. CCW, 128=center, 255=max. CW) 0E COMP level setting (0=0 to 255=10) 0F Break-IN delay setting (0=2.0 d to 255=13.0 d) 12 NB level setting (0=0% to 255=100%) 16 VOX gain setting (0=0% to 255=100%) 17 Anti VOX gain setting (0=0% to 255=100%) 15 01 Read squelch condition 02 Read S-meter level 11 Read RF power meter 12 Read SWR meter 13 Read ALC meter 16 02 Preamp (0=OFF, 1=ON) 12 AGC selection (0=OFF, 1=Fast, 2=Slow.) 22 Noise blanker (0=OFF, 1=ON) 40 Noise reduction (0=OFF, 1=ON) 41 Auto notch (0=OFF, 1=ON) 44 Speech compressor (0=OFF, 1=ON) 46 VOX function (0=OFF, 1=ON) 47 Break-IN function (0=OFF, 1=semi BK-IN, 2=full BK-IN) 48 Manual notch (0=OFF, 1=ON) 4F Twin peak filter (0=OFF, 1=ON) 50 Dial lock function (0=OFF, 1=ON) 19 00 Read the transceiver ID 1A 00 Set/read memory contents An additional code, 0001−0201 (0200=P1, 0201=P2), must be added to specify the memory channel. 01 Set/read band stacking register contents (see p. 91 for details) 02 Set/read the selected filter width (SSB, CW, RTTY: 0=50 Hz to 40/31=3600/2700 Hz; AM: 0=200 Hz to 39=8 kHz) 0301 Set/read RF power setting (0=minimum to 255=100%) 0302 Set/read MIC gain setting (0=0% to 255=100%)