Intermec PM23c PM23c, PM43, and PM43c Mid-Range Printer User Manual - Page 56

Calculate RFID Tag Position, Wizard > Calibration > RFID, Calibration, Enable

Get Intermec PM23c PDF manuals and user guides View all Intermec PM23c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Chapter 2 - Set Up the Printer 2 From the Main Menu, select Wizard > Calibration > RFID Calibration. 3 To enable the RFID module, select Enable. 4 Load the RFID media. 5 Select OK. When the calibration is complete, the printer displays the RFID Tag Position and Output Power (UHF inlays, only). Calculate RFID Tag Position You can perform a manual calculation to come up with an estimate of the RFID Tag Position. Because this value is an estimate, you may need to slightly adjust the calculated value to achieve the best results. Note: You do not need to calculate the Tag Position value for the PM23c printer. By default, the Tag Position is set to -13.5 mm and the yAntDist is 135 mm (pivoted antenna) or 136 mm (flat antenna). 1 Make sure Start Adjust and Stop Adjust are set to 0. 2 Measure the yChip value, which is the distance between the RFID chip and the media edge aligned with the tear bar. -BCFMUPQ PGGPSN .FEJBFEHF BMJHOFEXJUI UFBSCBS /FYUMBCFM 3'*%DIJQ Z$IJQ 42 PM23c, PM43, and PM43c Mid-Range Printer User Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
Chapter 2 — Set Up the Printer
42
PM23c, PM43, and PM43c Mid-Range Printer User Manual
2
From the Main Menu, select
Wizard > Calibration > RFID
Calibration
.
3
To enable the RFID module, select
Enable
.
4
Load the RFID media.
5
Select
OK
.
When the calibration is complete, the printer displays the RFID
Tag Position and Output Power (UHF inlays, only).
Calculate RFID Tag Position
You can perform a manual calculation to come up with an estimate of
the RFID Tag Position. Because this value is an estimate, you may need
to slightly adjust the calculated value to achieve the best results.
1
Make sure Start Adjust and Stop Adjust are set to 0.
2
Measure the yChip value, which is the distance between the RFID
chip and the media edge aligned with the tear bar.
Note:
You do not need to calculate the Tag Position value for the
PM23c printer. By default, the Tag Position is set to -13.5 mm and the
yAntDist is 135 mm (pivoted antenna) or 136 mm (flat antenna).