Panasonic CS-E18SD3UAW service manual - Page 39

Remove the bottom case., Attention, Mount to the wall., Preparation

Get Panasonic CS-E18SD3UAW PDF manuals and user guides View all Panasonic CS-E18SD3UAW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Mounting Remote Controller Receiver Install the remote controller receiver cable at least 1 31/32" (50 mm) away from electric wires of other appliances to avoid miss-operation (electromagnetic noise). 1 Remove the bottom case. Attention Mounting the bottom case  Tighten the screws securely until the screw heads touch the bottom case. (Otherwise, loose screw heads may hit the PCB and cause malfunction when mounting the top case.)  Do not over-tighten the screws. (The bottom case may be deformed, resulting in fall of the unit.) Insert the driver and slightly turn. Bottom case Flat-blade screwdriver Screws 6 Connecting the remote control wiring  Arrange the wires as shown in the illustration for 2 as in diagram below, avoiding unnecessary wires being stored in the case. (Caught wires may destroy the PCB.)  Avoid wires touching parts on the PCB. (Caught wires may destroy the PCB.) 2 Mount to the wall. EXPOSED TYPE EMBEDDED TYPE Preparation: Make 2 holes for screws using a driver. Preparation: Make 2 holes for screws using a driver. Mount the top case. • Align the claws of the top case and then align the claws of the bottom case. Cut here with a nipper and remove the burr with a file. Mount the bottom case to the wall. Mount the top case. • Align the claws of the top case and then align the claws of the bottom case. Avoid the wire being caught. Claw (2 places) Mount the bottom case to the wall. • Pass the wire through the hole in the centre of the bottom case. Claw (2 places) Wall to fix the receiver Claw Hole for screw Wood screw (supplied) Connect the remote control wiring. • Arrange the wires along the groove of the case. Clamper 7 (supplied) Pass through the hole Top case (Back side) Bottom case (Back side) 39 Claw Hole for screw Wood screw (supplied) Connect the remote control wiring. Terminal board Top case (Back side) Bottom case (Back side)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
39
Mounting Remote Controller Receiver
Install the remote controller receiver cable at least 1 31/32" (50 mm) away from electric wires of other appliances to avoid miss-operation
(electromagnetic noise).
1
Remove the bottom case.
Insert the driver
and slightly turn.
Bottom
case
Flat-blade
screwdriver
Attention
Mounting the bottom case
Tighten the screws securely until the screw heads
touch the bottom case. (Otherwise, loose screw
heads may hit the PCB and cause malfunction
when mounting the top case.)
Do not over-tighten the screws. (The bottom case
may be deformed, resulting in fall of the unit.)
Screws
6
Connecting the remote control wiring
Arrange the wires as shown in the illustration for
2
as in diagram below, avoiding unnecessary wires being
stored in the case. (Caught wires may destroy the PCB.)
Avoid wires touching parts on the PCB. (Caught wires may destroy the PCB.)
2
Mount to the wall.
EXPOSED TYPE
Preparation:
Make 2 holes for screws using a driver.
Mount the top case.
• Align the claws of the
top case and then align
the claws of the bottom
case.
Mount the bottom case
to the wall.
Connect the remote control wiring.
• Arrange the wires along the groove of the case.
Cut here with
a nipper and
remove the burr
with a file.
Hole for screw
Claw (2 places)
Wall to fix the
receiver
Wood screw (supplied)
Claw
Clamper
7
(supplied)
Pass
through
the hole
Top case
(Back side)
Bottom case (Back side)
EMBEDDED TYPE
Preparation:
Make 2 holes for screws using a driver.
Mount the top case.
• Align the claws of the
top case and then
align the claws of the
bottom case.
Mount the bottom case to the wall.
• Pass the wire through the hole in
the centre of the bottom case.
Connect the remote control wiring.
Avoid the wire
being caught.
Claw (2 places)
Hole for screw
Claw
Wood screw (supplied)
Terminal board
Top case
(Back side)
Bottom case (Back side)