Panasonic CS-E18SD3UAW service manual - Page 69

Breakdown Self Diagnosis Function

Get Panasonic CS-E18SD3UAW PDF manuals and user guides View all Panasonic CS-E18SD3UAW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

15.3 Breakdown Self Diagnosis Function 15.3.1 Self Diagnosis Function (Three Digits Alphanumeric Code)  Once abnormality has occurred during operation, the unit will stop its operation, and OFF/ON operation LED OFF.  OFF indicator does not shown on remote control display.  In operation after breakdown repair, the last error code abnormality will be stored in EEPROM.  To make a diagnosis 1 OFF/ON operation LED OFF and the unit automatically stops the operation, but the OFF indicator does not shown. 2 Press CHECK button continuously for 5 seconds. 3 "- -" will be displayed on the remote controller display. 4 Press timer ▲ or ▼ button on the remote control. The error code "H00" (no abnormality) will be displayed. 5 Every press of the button (▲ or ▼) will increase the error code number. 6 When the displayed error code matches the unit's error code, OFF/ON operation LED will be ON continuously. 7 The breakdown diagnosis mode will be cancelled by pressing CHECK button continuously for 5 seconds or wait for 30 seconds.  AC Reset button When AC Reset button is pressed, the error code will be reset so that the unit will be able to operate and recheck if any error occurred. "Check" button  To display memorized error status: 1 Turn ON the power supply. 2 Press CHECK button continuously for 5 seconds. 3 "- -" will be displayed on the remote controller display. 4 Press timer ▲ or ▼ button on the remote control. The error code "H00" (no abnormality) will be displayed. 5 Every press of the button (▲ or ▼) will increase the error code number. 6 When the displayed error code matches the unit's error code, OFF/ON operation LED will be ON continuously. 7 The breakdown diagnosis mode will be cancelled by pressing CHECK button continuously for 5 seconds or wait for 30 seconds. 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
69
15.3 Breakdown Self Diagnosis Function
15.3.1
Self Diagnosis Function (Three Digits Alphanumeric Code)
Once abnormality has occurred during operation, the unit will stop its operation, and OFF/ON operation LED OFF.
OFF indicator does not shown on remote control display.
In operation after breakdown repair, the last error code abnormality will be stored in EEPROM.
To make a diagnosis
1
OFF/ON operation LED OFF and the unit automatically stops the operation, but the OFF indicator does not
shown.
2
Press CHECK button continuously for 5 seconds.
3
“- -” will be displayed on the remote controller display.
4
Press timer
▲
or
▼
button on the remote control. The error code “H00” (no abnormality) will be displayed.
5
Every press of the button (
▲
or
▼
) will increase the error code number.
6
When the displayed error code matches the unit's error code, OFF/ON operation LED will be ON
continuously.
7
The breakdown diagnosis mode will be cancelled by pressing CHECK button continuously for 5 seconds or
wait for 30 seconds.
AC Reset button
When AC Reset button is pressed, the error code
will be reset so that the unit will be able to operate
and recheck if any error occurred.
“Check” button
To display memorized error status:
1
Turn ON the power supply.
2
Press CHECK button continuously for 5 seconds.
3
“- -” will be displayed on the remote controller display.
4
Press timer
▲
or
▼
button on the remote control. The error code "H00" (no abnormality) will be displayed.
5
Every press of the button (
▲
or
▼
) will increase the error code number.
6
When the displayed error code matches the unit's error code, OFF/ON operation LED will be ON
continuously.
7
The breakdown diagnosis mode will be cancelled by pressing CHECK button continuously for 5 seconds or
wait for 30 seconds.