Panasonic UF-4500 Operating Instructions - Page 138

Setting the Network Parameters

Page 138 highlights

Panasonic Document Management System (UF-5500 Only) Setting the Network Parameters Setting the User (Network) Parameters For your machine to be able to operate on the Network properly, the following three (3) Basic Parameters must be pre-programmed into the machine. (For UF-5500 only) If DHCP server is available on your network, the IP Address, Subnet Mask and Default Gateway IP Address will be acquired automatically. • IP Address • Subnet Mask • Default Gateway IP Address If the DHCP Server is not available, change the setting of the Fax Parameter No. 169 (DHCP CLIENT) to "INVALID", and then enter the IP Address instead. 1 7 SET MODE (1-8) ENTER NO. OR ∨∧ 21 USER PARAMETERS? PRESS SET 3 KEY OPERATOR ID ENTER ID= 4 Enter the Key Operator Password. 5 KEY OPERATOR ID ENTER ID=****** IP ADDRESS repeatedly until display shows; 6 Enter the IP Address using the keypad. Press period ".". (See Note 2) to enter the IP ADDRESS 123.178.240.3 Ex: 1 2 3 178 240 3 7 SUBNET MASK NOTE 1. To scroll the display to desired User Parameter in Step 5, press or . 2. For convenience, you can use to enter a period "." while programming IP Addresses only. Otherwise is used to enter an asterisk under other conditions. 138

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200

138
Panasonic Document Management System (UF-5500 Only)
Setting the Network Parameters
For your machine to be able to operate on the Network properly, the following three (3) Basic Parameters
must be pre-programmed into the machine. (For UF-5500 only)
If DHCP server is available on your network, the IP Address, Subnet Mask and Default Gateway IP Address
will be acquired automatically.
• IP Address
• Subnet Mask
• Default Gateway IP Address
If the DHCP Server is not available, change the setting of the Fax Parameter No. 169 (DHCP CLIENT) to
"INVALID", and then enter the IP Address instead.
NOTE
1.
To scroll the display to desired User Parameter in Step 5, press
or
.
2.
For convenience, you can use
to enter a period "." while programming IP Addresses only.
Otherwise
is used to enter an asterisk under other conditions.
Setting the User (Network) Parameters
1
SET MODE
(1-8)
ENTER NO. OR
∨∧
2
USER PARAMETERS?
PRESS SET
3
KEY OPERATOR ID
ENTER ID=
]
4
Enter the Key Operator Password.
KEY OPERATOR ID
ENTER ID=******
5
repeatedly until display shows;
IP ADDRESS
]
6
Enter the IP Address using the keypad. Press
to enter the
period ".". (See Note 2)
Ex:
IP ADDRESS
123.178.240.3
]
7
SUBNET MASK
]
7
1
1
2
3
1
7
8
2
4
0
3