Sony PMW320K Product Manual (PMW320 Operating Instruction) - Page 45

Attaching a UHF Portable Tuner (for a UHF Wireless Microphone System), To fit the DWR-S01D or WRR-855S

Get Sony PMW320K PDF manuals and user guides View all Sony PMW320K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Chapter 2 Preparations 1 AUDIO IN selectors 2 Monaural microphone 3 AUDIO IN CH1/CH2 switches 4 To AUDIO IN CH1 or CH2 connector 4 Switch the input level to match the sensitivity of the microphone used. Switch the input level by changing the setting of MAINTENANCE >Audio >Rear MIC CH1/ CH2 Ref in the setup menu (factory default setting is -60 dB). For details, see page 118. Notes • If the input level on the camcorder is not at an appropriate setting for the microphone sensitivity, loud sounds may be distorted, and the signal-to-noise ratio may be affected. • In order for the AUDIO IN CH1 and CH2 connectors on the camcorder to be able to provide a phantom 48 V power supply, female XLR connectors (3-pin) are fitted. If the microphone cable has a female connector, use an adaptor. • When you detach a CAC-12 Microphone Holder once you have attached to the camcorder, be careful not to lose the two screws fixing the CAC-12 (in step 1). After detaching the CAC-12, be sure to put the two screws back into their original places. Attaching a UHF Portable Tuner (for a UHF Wireless Microphone System) To use a Sony UHF wireless microphone system, power the camcorder off and then fit one of the following UHF portable tuners. • DWR-S01D Digital Wireless Receiver • WRR-855S UHF Synthesized Tuner Unit • WRR-860A/861/862 UHF Synthesized Diversity Tuner For details of these units, refer to the operation manuals for them. Note The optional WRR Mount Bracket (service part number: A-8278-057-B) is required to fit the WRR-862. For details, contact your vendor or a Sony service representative To fit the DWR-S01D or WRR-855S 1 Remove the four fixing screws holding the cover of the portable tuner/receiver housing slot located in the rear of the camcorder, to remove the cover. 2 Insert the DWR-S01D or WRR-855S into the housing slot, and fasten the four fixing screws. DWR-S01D or WRR-855S 3 Set the AUDIO IN selector for the channel to which you want to input audio signal to WIRELESS (see page 22). Preparing the Audio Input System 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
Preparing the Audio Input System
45
Chapter 2
Preparations
4
Switch the input level to match the
sensitivity of the microphone used.
Switch the input level by changing the setting of
MAINTENANCE >Audio >Rear MIC CH1/
CH2 Ref in the setup menu (factory default
setting is –60 dB).
For details, see page 118
.
Notes
•
If the input level on the camcorder is not at an
appropriate setting for the microphone sensitivity, loud
sounds may be distorted, and the signal-to-noise ratio
may be affected.
•
In order for the AUDIO IN CH1 and CH2 connectors
on the camcorder to be able to provide a phantom 48 V
power supply, female XLR connectors (3-pin) are
fitted. If the microphone cable has a female connector,
use an adaptor.
•
When you detach a CAC-12 Microphone Holder once
you have attached to the camcorder, be careful not to
lose the two screws fixing the CAC-12 (in step
1
).
After detaching the CAC-12, be sure to put the two
screws back into their original places.
To use a Sony UHF wireless microphone system,
power the camcorder off and then fit one of the
following UHF portable tuners.
•
DWR-S01D Digital Wireless Receiver
•
WRR-855S UHF Synthesized Tuner Unit
•
WRR-860A/861/862 UHF Synthesized
Diversity Tuner
For details of these units, refer to the operation
manuals for them.
Note
The optional WRR Mount Bracket (service part number:
A-8278-057-B) is required to fit the WRR-862.
For details, contact your vendor or a Sony service
representative
To fit the DWR-S01D or WRR-855S
1
Remove the four fixing screws holding
the cover of the portable tuner/receiver
housing slot located in the rear of the
camcorder, to remove the cover.
2
Insert the DWR-S01D or WRR-855S
into the housing slot, and fasten the four
fixing screws.
3
Set the AUDIO IN selector for the
channel to which you want to input
audio signal to WIRELESS
(see
page 22)
.
Attaching a UHF Portable Tuner
(for a UHF Wireless Microphone
System)
1
AUDIO IN selectors
2
Monaural microphone
3
AUDIO IN CH1/CH2 switches
4
To AUDIO IN CH1 or CH2 connector
DWR-S01D or WRR-855S