Home » Sony Manuals » Video Cameras » Sony PMW320K » Manual Viewer

Sony PMW320K Product Manual (PMW320 Operating Instruction) - Page 63

To lock the timecode to an external, source, Set the F-RUN/SET/R-RUN switch

Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Chapter 3 Adjustments and Settings Example 2: Interconnecting a number of camcorders (including one reference camcorder) To another camcorder to be synchronized 1 VIDEO OUT connector 2 TC OUT connector 3 TC IN connector 4 GENLOCK IN connector To lock the timecode to an external source 1 Turn on the POWER switch. 2 Set the PRESET/REGEN/CLOCK switch to PRESET. 3 Set the F-RUN/SET/R-RUN switch to F-RUN. 4 Set the DISPLAY switch to TC. 5 Supply a timecode signal and a reference video signal complying with the SMPTE standard and in proper phase relationship, to the TC IN connector and to the GENLOCK IN connector, respectively. This operation synchronizes the internal timecode generator with the external timecode. After about 10 seconds, you can disconnect the external timecode without losing the synchronization. Notes • When you finish the above procedure, the internal timecode is immediately synchronized with the external timecode and the counter display will show the value of the external timecode. However, wait for a few seconds until the sync generator stabilizes before recording. • If the frequency of the reference video signal is not the same as the system frequency of the camcorder, the camcorder cannot be correctly genlocked. In such a case, the internal timecode is not correctly synchronized with the external timecode. User bit settings during timecode synchronization When the timecode is synchronized, only the time data is synchronized with the external timecode value. To release the timecode synchronization First disconnect the external timecode, then set the F-RUN/SET/R-RUN switch to R-RUN. To change the power supply from the battery pack to an external power supply during timecode synchronization To maintain a continuous power supply, connect the external power supply to the DC IN connector before removing the battery pack. You may lose timecode synchronization if you remove the battery pack first. Camcorder synchronization during timecode synchronization During timecode synchronization, the camcorder is genlocked to the reference video signal input from the GENLOCK IN connector. Setting the Time Data 63

Section	Page
Table of Contents	5
Foreword	10
Before Use	10
Chapter 1 Overview	11
Features	11
Using the CD-ROM	12
Reading the CD-ROM Manuals	12
System Requirements for Using the Applications	13
Software Installation	13
Locations and Functions of Parts and Controls	14
Power Supply	14
Accessory Attachments	14
Operating and Connectors Section	16
Monochrome LCD Panel	25
Auto Focus Lens (Supplied with the PMW-320K)	26
Viewfinder	27
Viewfinder Screen Display	29
Chapter 2 Preparations	33
Preparing a Power Supply	33
Using a Battery Pack	33
Using AC Power	34
Attaching the Viewfinder	35
Attaching the Supplied Viewfinder	35
Adjusting the Viewfinder Position	35
Adjusting the Viewfinder Angle	36
Lifting Up the Viewfinder Barrel and Eyepiece	36
Adjusting the Viewfinder Focus and Screen	37
Using the BKW-401 Viewfinder Rotation Bracket	37
Attaching a 5-inch Electronic Viewfinder	38
Setting the Area of Use	40
Setting the Date/Time of the Internal Clock	41
Mounting and Adjusting the Lens	41
Adjusting the Flange Focal Length	42
Preparing the Audio Input System	43
Connecting a Microphone to the MIC IN Connector	43
Connecting Microphones to the AUDIO IN Connectors	44
Attaching a UHF Portable Tuner (for a UHF Wireless Microphone System)	45
Tripod Mounting	46
Connecting a Video Light	47
Using the Shoulder Strap	47
Adjusting the Shoulder Pad Position	48
Chapter 3 Adjustments and Settings	49
Setting the Video Format	49
Changing the Video Format	50
Adjusting the Black Balance and the White Balance	50
Adjusting the Black Balance	50
Adjusting the White Balance	51
Setting the Electronic Shutter	54
Shutter Modes	54
Selecting the Shutter Mode and Shutter Speed	54
Changing the Reference Value for Automatic Iris Adjustment	56
Zooming	57
Switching between Zoom Modes	57
Using Manual Zoom	57
Using Servo Zoom	57
Adjusting the Focus	57
Adjusting in Full MF Mode	57
Adjusting in MF Mode	58
Adjusting in AF Mode	58
Using Macro Mode	58
Adjusting the Audio Level	59
Manually Adjusting the Audio Levels of the Audio Inputs from the AUDIO IN CH1/CH2 Connectors	59
Manually Adjusting the Audio Level of the MIC IN Connector	59
Recording Audio on Channels 3 and 4	60
Setting the Time Data	61
Setting the Timecode	61
Setting the User Bits	62
Synchronizing the Timecode	62
Checking Camcorder Settings and Status Information (Status Screens)	64
Chapter 4 Shooting	66
Handling S×S Memory Cards	66
About S×S Memory Cards	66
Loading and Ejecting S×S Memory Cards	67
Selecting the S×S Memory Card to Use	68
Formatting (Initializing) S×S Memory Cards	68
Checking the Remaining Recording Time	69
Restoring S×S Memory Cards	69
Basic Operations	70
Playing Recorded Clips	71
Deleting Recorded Clips	72
Advanced Operations	73
Recording Shot Marks	73
Setting OK Marks	73
Starting to Record from Pre-stored Video (Picture Cache Function)	73
Recording Time-lapse Video (Interval Rec Function)	75
Shooting Stop Motion Animations (Frame Rec Function)	76
Shooting with Slow & Quick Motion	77
Framing Shots with the Freeze Mix Function	79
Chapter 5 Clip Operations	80
Clip Playback	80
Thumbnail Screen	80
Playing Clips	82
Using Thumbnails to Search Inside Clips	83
Thumbnail Operations	84
THUMBNAIL Menu Configuration	84
Basic THUMBNAIL Menu Operations	85
Changing the Thumbnail Screen Type	85
Displaying Clip Properties	86
Adding and Deleting OK Marks (HD Mode Only)	87
Copying Clips	87
Deleting Clips	88
Displaying the Expand Thumbnail Screen	89
Displaying the Shot Mark Thumbnail Screen (HD Mode Only)	90
Adding and Deleting Shot Marks (HD Mode Only)	90
Changing Clip Index Pictures (HD Mode Only)	91
Dividing Clips (HD Mode Only)	91
Chapter 6 Menu and Detailed Settings	92
Setup Menu Organization and Levels	92
Setup Menu Organization	92
Setup Menu Levels	92
Basic Setup Menu Operations	93
Menu List	96
OPERATION Menu	96
PAINT Menu	110
MAINTENANCE Menu	116
FILE Menu	127
Assigning Functions to Assignable Switches	131
Functions that can be assigned to the ASSIGN. 0 switch	131
Functions that can be assigned to the ASSIGN. 2 switch	132
Functions that can be assigned to the ASSIGN. 1 and 3 switches, the ASSIGNABLE 4 and 5 switches, and the COLOR TEMP. button	132
Functions that can be assigned to the RET button on the lens	134
Adjusting Picture Characteristics to Match the PMW-EX1R	135
Chapter 7 Saving and Loading User Setting Data	136
Saving and Loading Settings	136
Saving Setting Data	136
Loading Setting Data	137
Resetting a File after Changing Its Contents	137
Saving and Loading Scene Files	138
Saving Scene Files	138
Loading Scene Files	138
Saving and Loading Lens Files	139
Setting Lens File Data	139
Saving Lens Files	139
Loading Lens Files	140
Loading Lens Files Automatically	140
Chapter 8 Connecting External Devices	141
Connecting External Monitors	141
Operating Clips with a Computer	143
Connecting an External Device (i.LINK Connection)	145
Recording the Camera Picture on an External Device	145
Nonlinear Editing	146
Recording External Input Signals	146
Chapter 9 Maintenance	148
Testing the Camcorder	148
Maintenance	148
Cleaning the Viewfinder	148
Note about the Battery Terminal	148
Operation Warnings	149
Appendix	156
Important Notes on Operation	156
Exchanging the Battery of the Internal Clock	158
Specifications	158
General	158
Camera Block	159
Audio Block	159
Display	159
Media Block	160
Inputs/Outputs	160
Lens Block (PMW-320K only)	160
Supplied Accessories	161
Recommended Additional Equipment	161
Chart of Optional Components and Accessories	163
About i.LINK	164
MPEG-2 Video Patent Portfolio License	165

Match case Limit results 1 per page

Setting the Time Data

Chapter 3

Adjustments and Settings

Example 2: Interconnecting a number of

camcorders (including one reference

camcorder)

To lock the timecode to an external

source

Turn on the POWER switch.

Set the PRESET/REGEN/CLOCK

switch to PRESET.

Set the F-RUN/SET/R-RUN switch to

F-RUN.

Set the DISPLAY switch to TC.

Supply a timecode signal and a

reference video signal complying with

the SMPTE standard and in proper

phase relationship, to the TC IN

connector and to the GENLOCK IN

connector, respectively.

This operation synchronizes the internal

timecode generator with the external

timecode. After about 10 seconds, you can

disconnect the external timecode without

losing the synchronization.

Notes

•

When you finish the above procedure, the internal

timecode is immediately synchronized with the

external timecode and the counter display will show

the value of the external timecode. However, wait for

a few seconds until the sync generator stabilizes before

recording.

•

If the frequency of the reference video signal is not the

same as the system frequency of the camcorder, the

camcorder cannot be correctly genlocked. In such a

case, the internal timecode is not correctly

synchronized with the external timecode.

User bit settings during timecode

synchronization

When the timecode is synchronized, only the time

data is synchronized with the external timecode

value.

To release the timecode synchronization

First disconnect the external timecode, then set

the F-RUN/SET/R-RUN switch to R-RUN.

To change the power supply from the battery

pack to an external power supply during

timecode synchronization

To maintain a continuous power supply, connect

the external power supply to the DC IN connector

before removing the battery pack. You may lose

timecode synchronization if you remove the

battery pack first.

Camcorder synchronization during timecode

synchronization

During timecode synchronization, the camcorder

is genlocked to the reference video signal input

from the GENLOCK IN connector.

VIDEO OUT connector

TC OUT connector

TC IN connector

GENLOCK IN connector

To another camcorder to be synchronized