TP-Link TL-SG2424P TL-SG2424P V1 User Guide 1910010774 - Page 149

Note:

For detailed introduction of TLV, please refer to IEEE 802.1AB standard and ANSI/TIA-1057.

In TP-LINK switch, the following LLDP optional TLVs are supported.

Port Description TLV

The Port Description TLV allows network management to

advertise the IEEE 802 LAN station's port description.

System Capabilities TLV

The System Capabilities TLV identifies the primary functions of

the system and whether or not these primary functions are

enabled.

System Description TLV

The System Description TLV allows network management to

advertise the system's description, which should include the full

name and version identification of the system's hardware type,

software operating system, and networking software.

System Name TLV

The System Name TLV allows network management to

advertise the system's assigned name, which should be the

system's fully qualified domain name.

Management Address TLV

The Management Address TLV identifies an address associated

with the local LLDP agent that may be used to reach higher

entities to assist discovery by network management.

Port VLAN ID TLV

The Port VLAN ID TLV allows a VLAN bridge port to advertise

the port's VLAN identifier (PVID) that will be associated with

untagged or priority tagged frames.

Port And Protocol VLAN ID

TLV

The Port And Protocol VLAN ID TLV allows a bridge port to

advertise a port and protocol VLAN ID.

VLAN Name TLV

The VLAN Name TLV allows an IEEE 802.1Q-compatible IEEE

802 LAN station to advertise the assigned name of any VLAN

with which it is configured.

Link Aggregation TLV

The Link Aggregation TLV indicates whether the link is capable

of being aggregated, whether the link is currently in an

aggregation, and if in an aggregation, the port identification of

the aggregation.

MAC/PHY

Configuration/Status TLV

The MAC/PHY Configuration/Status TLV identifies: a)The duplex

and bit-rate capability of the sending IEEE 802.3 LAN node that

is connected to the physical medium; b)The current duplex and

bit-rate settings of the sending IEEE 802.3 LAN node; c)Whether

these settings are the result of auto-negotiation during link

initiation or of manual set override action.

Max Frame Size TLV

The Maximum Frame Size TLV indicates the maximum frame

size capability of the implemented MAC and PHY.

Power Via MDI TLV

The Power Via MDI TLV allows network management to

advertise and discover the MDI power support capabilities of the

sending IEEE 802.3 LAN station.

141

Section	Page
Package Contents	9
Chapter 1 About this Guide	10
1.1 Intended Readers	10
1.2 Conventions	10
1.3 Overview of This Guide	10
Chapter 2 Introduction	13
2.1 Overview of the Switch	13
2.2 Main Features	13
2.3 Appearance Description	14
2.3.1 Front Panel	14
2.3.2 Rear Panel	15
Chapter 3 Login to the Switch	16
3.1 Login	16
3.2 Configuration	16
Chapter 4 System	18
4.1 System Info	18
4.1.1 System Summary	18
4.1.2 Device Description	20
4.1.3 System Time	20
4.1.4 Daylight Saving Time	21
4.1.5 System IP	23
4.2 User Management	24
4.2.1 User Table	24
4.2.2 User Config	24
4.3 System Tools	26
4.3.1 Config Restore	26
4.3.2 Config Backup	26
4.3.3 Firmware Upgrade	27
4.3.4 System Reboot	28
4.3.5 System Reset	28
4.4 Access Security	28
4.4.1 Access Control	29
4.4.2 SSL Config	30
4.4.3 SSH Config	31
Chapter 5 Switching	37
5.1 Port	37
5.1.1 Port Config	37
5.1.2 Port Mirror	38
5.1.3 Port Security	40
5.1.4 Port Isolation	42
5.1.5 Loopback Detection	43
5.2 LAG	44
5.2.1 LAG Table	45
5.2.2 Static LAG	46
5.2.3 LACP Config	47
5.3 Traffic Monitor	49
5.3.1 Traffic Summary	49
5.3.2 Traffic Statistics	50
5.4 MAC Address	52
5.4.1 Address Table	53
5.4.2 Static Address	54
5.4.3 Dynamic Address	55
5.4.4 Filtering Address	57
5.5 DHCP Filtering	58
Chapter 6 VLAN	62
6.1 802.1Q VLAN	63
6.1.1 VLAN Config	65
6.1.2 Port Config	67
6.2 Application Example for 802.1Q VLAN	69
Chapter 7 Spanning Tree	71
7.1 STP Config	76
7.1.1 STP Config	76
7.1.2 STP Summary	78
7.2 Port Config	78
7.3 MSTP Instance	80
7.3.1 Region Config	80
7.3.2 Instance Config	81
7.3.3 Instance Port Config	82
7.4 STP Security	84
7.4.1 Port Protect	84
7.4.2 TC Protect	87
7.5 Application Example for STP Function	87
Chapter 8 Multicast	91
8.1 IGMP Snooping	93
8.1.1 Snooping Config	94
8.1.2 Port Config	95
8.1.3 VLAN Config	96
8.1.4 Multicast VLAN	98
8.2 Multicast IP	101
8.2.1 Multicast IP Table	101
8.2.2 Static Multicast IP	102
8.3 Multicast Filter	103
8.3.1 IP-Range	103
8.3.2 Port Filter	104
8.4 Packet Statistics	106
Chapter 9 QoS	108
9.1 DiffServ	111
9.1.1 Port Priority	111
9.1.2 DSCP Priority	112
9.1.3 802.1P/CoS mapping	113
9.1.4 Schedule Mode	114
9.2 Bandwidth Control	115
9.2.1 Rate Limit	115
9.2.2 Storm Control	116
9.3 Voice VLAN	118
9.3.1 Global Config	120
9.3.2 Port Config	120
9.3.3 OUI Config	122
Chapter 10 PoE	124
10.1 PoE Config	124
10.1.1 PoE Config	125
10.1.2 PoE Profile	126
10.2 PoE Time-Range	127
10.2.1 Time-Range Summary	127
10.2.2 PoE Time-Range Create	128
10.2.3 PoE Holiday Config	129
Chapter 11 SNMP	130
11.1 SNMP Config	132
11.1.1 Global Config	132
11.1.2 SNMP View	133
11.1.3 SNMP Group	134
11.1.4 SNMP User	135
11.1.5 SNMP Community	137
11.2 Notification	139
11.3 RMON	141
11.3.1 History Control	142
11.3.2 Event Config	142
11.3.3 Alarm Config	143
Chapter 12 LLDP	146
12.1 Basic Config	150
12.1.1 Global Config	150
12.1.2 Port Config	151
12.2 Device Info	152
12.2.1 Local Info	152
12.2.2 Neighbor Info	153
12.3 Device Statistics	153
12.4 LLDP-MED	155
12.4.1 Global Config	156
12.4.2 Port Config	156
12.4.3 Local Info	158
12.4.4 Neighbor Info	159
Chapter 13 Maintenance	161
13.1 System Monitor	161
13.1.1 CPU Monitor	161
13.1.2 Memory Monitor	162
13.2 Log	162
13.2.1 Log Table	163
13.2.2 Local Log	164
13.2.3 Remote Log	165
13.2.4 Backup Log	165
13.3 Device Diagnostics	166
13.3.1 Cable Test	166
13.3.2 Loopback	167
13.4 Network Diagnostics	168
13.4.1 Ping	168
13.4.2 Tracert	168
Appendix A: Specifications	170
Appendix B: Configuring the PCs	171

TP-Link TL-SG2424P TL-SG2424P V1 User Guide 1910010774 - Page 149

Port And Protocol VLAN ID

Page 149 highlights