Brother International SE-270D Users Manual - English
Brother International SE-270D Manual
 |
View all Brother International SE-270D manuals
Add to My Manuals
Save this manual to your list of manuals |
Brother International SE-270D manual content summary:
- Brother International SE-270D | Users Manual - English - Page 1
GETTING READY SEWING BASICS UTILITY STITCHES EMBROIDERY APPENDIX CPS5XV[Y Easy Thread Cassette System Operation Manual - Brother International SE-270D | Users Manual - English - Page 2
contact your retailer. Accessories Note (For U.S.A. only) z Foot controller: Model N5V This foot controller can be used on this machine model SE-270D. z The screw of the presser foot holder is available through your authorized dealer. (Part code: XA4813-051) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10 - Brother International SE-270D | Users Manual - English - Page 3
onto this spool pin in order to wind the bobbin. n Bobbin storage compartment Store the bobbins designed specifically for this sewing machine in this compartment. o Bobbin winder cover Open this cover when winding the bobbin. p Thread guide for bobbin winding Pass the thread around this thread - Brother International SE-270D | Users Manual - English - Page 4
. g Presser foot holder The presser foot is installed onto the presser foot holder. 4 8 5 7 6 a Handle Carry the sewing machine by its handle when transporting the machine. b Balance wheel Turn the balance wheel toward you to raise and lower the needle to sew one stitch. c Embroidery card slot - Brother International SE-270D | Users Manual - English - Page 5
to start or stop sewing. The machine sews at a slow speed at the beginning of sewing while the button is depressed. When sewing is stopped, the needle is lowered in the fabric. For details, refer to "Starting to sew" (page 47). e Presser foot lever Raise and lower the presser foot lever to raise and - Brother International SE-270D | Users Manual - English - Page 6
memory. h Sewing machine help key Press to get help on using the sewing machine. Displays simple explanations of setting upper thread / bobbin winding / setting bobbin thread / needle replacement / embroidery unit attachment / embroidery frame attachment / embroidery foot attachment / presser foot - Brother International SE-270D | Users Manual - English - Page 7
Thank you for purchasing this sewing machine. Before using this sewing machine, carefully read the "Important Safety Instructions" (page 5), and then study this manual for the correct operation of the various functions. In addition, after you have finished reading this manual, store it where it can - Brother International SE-270D | Users Manual - English - Page 8
Names of Machine Parts and Their Functions Cover B Front view ...Cover B Needle and presser foot section ...Cover C Right-side/rear view ...Cover C Operation buttons ...Cover D Operation panel ...Cover E Introduction ...1 Sewing Machine Features ...1 Important Safety Instructions 5 GETTING READY - Brother International SE-270D | Users Manual - English - Page 9
61 UTILITY STITCHES 63 Stitch Settings...64 Utility stitches ...64 Overcasting Stitches...69 Sewing overcasting stitches using overcasting foot "G 69 Sewing overcasting stitches using zigzag foot "J 70 Sewing overcasting stitches using the optional side cutter 71 Basic Stitching ...73 Basting - Brother International SE-270D | Users Manual - English - Page 10
out partway through a design...142 Stopping while embroidering ...142 APPENDIX 145 Maintenance...146 Cleaning the machine surface ...146 Cleaning the shuttle ...146 Troubleshooting ...148 Error messages ...153 Nothing appears in the LCD ...155 Operation beep ...155 Cancelling the operation beep - Brother International SE-270D | Users Manual - English - Page 11
, changing needle, threading bobbin, or changing presser foot, and the like. 15.Always unplug the machine from the electrical outlet when removing covers, lubricating, or when making any other user servicing adjustments mentioned in the instruction manual. 16.This sewing machine is not intended for - Brother International SE-270D | Users Manual - English - Page 12
IN THE UK, EIRE, MALTA AND CYPRUS ONLY If this machine is fitted with a three-pin non-rewireable BS plug then OR GREEN AND YELLOW. The wires in this main lead are colored in accordance with the following code: Blue Neutral Brown Live As the colors of the wiring in the main lead of this - Brother International SE-270D | Users Manual - English - Page 13
installation. For repair or adjustment In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Brother dealer. For - Brother International SE-270D | Users Manual - English - Page 14
8 - Brother International SE-270D | Users Manual - English - Page 15
various preparations required before starting to sew are described in this chapter. Turning the Machine On/Off 10 LCD (liquid crystal display) operation 12 Winding/Installing the Bobbin 16 Upper Threading ...21 Replacing the Needle 33 Replacing the Presser Foot 38 Sewing Cylindrical Pieces 41 - Brother International SE-270D | Users Manual - English - Page 16
On/Off This section explains how to turn the sewing machine on and off. Power supply precautions Be sure . If the cord or plug is damaged, take the machine to your authorized dealer for repairs before continuing use. ● Unplug the power cord if the machine is not to be used for a long period of time - Brother International SE-270D | Users Manual - English - Page 17
cord into the power supply jack on the right side of the Make sure that the machine is not sewing. a machine. Press the left side of the main power switch on b the right side of the machine (set it to " "). Insert the plug of the power supply cord into a b household electrical outlet. 1 a Power - Brother International SE-270D | Users Manual - English - Page 18
stitch selection screen 1 6 2 7 3 4 5 a Selected stitch b Presser foot to be used c Stitches d Stitch width (mm) e Stitch length (mm when the embroidery unit is attached. z Refer to "Error messages" (page 153) for messages displayed on the LCD. z Depending on the model of sewing machine, an - Brother International SE-270D | Users Manual - English - Page 19
machine operations and sewing settings can be changed. The stitch or machine attributes that can be set are listed below. 1 Attribute Icon Details Settings Thread color/ needle count You can switch among thread color/thread number/needle count when embroidering. Thread color/Embroidery - Brother International SE-270D | Users Manual - English - Page 20
X The initial screen appears again. Note z The "Thread color index" is the color number display used when embroidery cards made by "PE-Design" are used. z The "NO." is the number for the sewing machine. z Settings that are changed are not lost when the power is turned off. • The items shown in - Brother International SE-270D | Users Manual - English - Page 21
winding / setting bobbin thread / needle † Example: Upper threading 1 replacement / embroidery unit attachment / embroidery frame attachment / embroidery foot attachment / presser foot replacement on the LCD. Turn on the sewing machine. a X The LCD comes on. Press (Sewing machine help key - Brother International SE-270D | Users Manual - English - Page 22
in injuries or damage to the machine. ● The included bobbin was designed specifically for this sewing machine. If bobbins from older models are used, the machine will not operate correctly. Use only the included bobbin or bobbins of the same type (part code: SA156, SFB:XA5539-151). Actual size - Brother International SE-270D | Users Manual - English - Page 23
too small for the spool being used, the thread may catch on the slit in the spool or the needle may break. ● • Use the special Brother embroidery bobbin thread when embroidering. Note z If a spool of thread 12 mm (1/2 inch) in diameter and 75 mm (3 inch) high is inserted onto the - Brother International SE-270D | Users Manual - English - Page 24
controller to the right k (so that the speed will be fast). 1 2 a Sewing speed controller Press l (Start/stop button) once. a Thread guide for bobbin winding b Two slits Wind the thread that was pulled out onto the i bobbin. Wind the thread that was pulled clockwise five or six times without - Brother International SE-270D | Users Manual - English - Page 25
to the left. o Remove the bobbin from the shaft. p ● The bobbin was designed specifically for this sewing machine. If bobbins from older models are used, the machine will not operate correctly. Use only the included bobbin or bobbins of the same type (part code: SA156, SFB:XA5539-151). Actual - Brother International SE-270D | Users Manual - English - Page 26
. Be sure to thread the machine as indicated. Lightly hold down the bobbin with your right e hand, and then guide the thread as shown with your left hand. 1 a Tension-adjusting spring Reattach the bobbin cover. g Insert the tab in the lower-left corner of the bobbin cover, and then lightly press - Brother International SE-270D | Users Manual - English - Page 27
instructions. If the upper threading is not correct, the thread may become tangled or the needle may bend or break. About the spool of thread With this sewing machine slightly larger than the diameter of the spool. 1 2 3 a Spool cap (large) b Spool cap (small) c Spool Memo z For details on using the - Brother International SE-270D | Users Manual - English - Page 28
for threading the thread cassette is indicated on the thread cassette. Also check the markings on the thread cassette while threading it. Turn on the sewing machine. a Open the thread cassette compartment cover b at the top on the left side of the - Brother International SE-270D | Users Manual - English - Page 29
off the spool cap that is inserted onto the spool pin. 1 1 2 3 1 a Thread cassette eject lever X The thread cassette is raised. • If the sewing machine is turned off, the thread cassette will not be ejected correctly. Remove the thread cassette. d a Spool cap (orange) b Spool pin c Cover Place - Brother International SE-270D | Users Manual - English - Page 30
j the slit along the left side of the thread cassette. Follow arrow 3 indicated on the thread cassette. Pass the thread through the notch in the l lower-right corner of the thread cassette, and then pull the thread to the left. Follow arrow 5 indicated on the thread cassette. 1 a Notch 24 - Brother International SE-270D | Users Manual - English - Page 31
thread under the disc at the front in m the lower-left corner and around to the right, Threading the same time that the thread cassette is inserted. Memo z The needle threader can be used with sewing machine needles 75/11 through 100/16. z Thread with a thickness of 130/20 or thicker cannot - Brother International SE-270D | Users Manual - English - Page 32
• The thread cassette can be inserted whenever the presser foot lever is raised or lowered. However, when the side cutter is attached, be sure to lower the presser foot lever before installing the thread cassette. For more details, refer to "Sewing overcasting stitches using the optional side cutter - Brother International SE-270D | Users Manual - English - Page 33
the thread through the presser foot, and d then pull out about 10-15 cm (3/8-5/8 inch) of thread toward the rear of the machine. Place the spool of 1 X Now that the upper threading and the lower threading are finished, you are ready to begin sewing. • When embroidering, go to c in "Embroidering - Brother International SE-270D | Users Manual - English - Page 34
thread d from the spool on the extra spool pin. Thread the needle manually (without using the needle threader) • For more details, refer to " be used with the needle threader, be sure to remove the needle, otherwise the machine may be damaged. Check that the thread cassette indicator is lit b up in - Brother International SE-270D | Users Manual - English - Page 35
c onto the extra spool pin. Using the twin needle, you can sew two parallel lines of the same stitch with two different colors. Both CAUTION ● Only use the twin needle (Part code : X59296-051). Use of any other needle may bend the needle or damage the machine. ● Never use bent needles. Bent - Brother International SE-270D | Users Manual - English - Page 36
with the g thread for the left side of the stitch. • For details, refer to "Thread the needle manually (without using the needle threader)" (page 28). Turn on the sewing machine and select a j stitch. • For stitch selection see "Selecting stitching" (page 45). • See "Stitch Settings" (page 64) for - Brother International SE-270D | Users Manual - English - Page 37
button) twice to raise the needle. 1 Note z When changing the sewing direction, press (Needle position button) to raise the needle from the fabric, and then raise the presser foot lever and turn the fabric. a Needle position button X The bobbin thread is looped around the upper thread and can be - Brother International SE-270D | Users Manual - English - Page 38
GETTING READY Pull out about 10-15 cm (4-5 inches) of the e bobbin thread under the presser foot toward the rear of the machine. Reattach the bobbin cover. f Insert the tab in the lower-left corner of the bobbin cover, and then lightly press down on the right side. 2 1 32 - Brother International SE-270D | Users Manual - English - Page 39
breaks and fragments are dispersed. Be sure to read and carefully follow the instructions below. CAUTION ● Only use home sewing machine needles. Use of any other needle may bend the needle or damage the machine. ● Never use bent needles. Bent needles can easily break, possibly resulting in injuries - Brother International SE-270D | Users Manual - English - Page 40
/14 65/9-90/14 90/14-100/16 ■ Thread and needle number The lower the thread number is, the larger the thread, and the larger the needle 16 needle, regardless of the fabric or thread. ■ Embroidery needles Use a 75/11 home sewing machine needle. When embroidering on thick fabrics such as denim, use - Brother International SE-270D | Users Manual - English - Page 41
a bent needle. 1 a Flat surface CAUTION ● Before replacing the needle, be sure to turn off the sewing machine, otherwise injuries may occur if the start/stop button is accidentally pressed and the machine starts sewing. Lower the presser foot lever. c 1 a Presser foot lever Replacing the Needle 35 - Brother International SE-270D | Users Manual - English - Page 42
needle. 1 2 a Screwdriver b Needle clamp screw • Do not apply a strong force when loosening or tightening the needle clamp screw, otherwise certain parts of the sewing machine may be damaged. CAUTION ● Be sure to insert the needle until it touches the needle stopper and securely tighten the needle - Brother International SE-270D | Users Manual - English - Page 43
use the screwdriver to tighten the needle clamp screw. 1 Lower the needle-changing tool. d X The needle is installed. Lower the needle-changing tool off of the h needle. side of the needle toward the rear of the machine. Lift up the needle-changing tool so that the f fork hooks onto the - Brother International SE-270D | Users Manual - English - Page 44
, causing the needle to bend or break. ● Only use presser feet designed specifically for this sewing machine. Use of any other presser foot may result in injuries or damage to the machine. Replacing the presser foot Replace the presser foot as described below. Press (Needle position button) once or - Brother International SE-270D | Users Manual - English - Page 45
the sewing machine, attach the correct presser foot, and then select the desired stitch again. 2 3 a Presser foot holder b Notch c Pin Slowly lower the presser foot lever so that the f presser foot pin snaps into the notch in the presser foot holder. 1 a Presser foot lever X The presser foot - Brother International SE-270D | Users Manual - English - Page 46
hand. Remove the presser foot holder when cleaning the sewing machine or when installing a presser foot that does not use the presser foot holder, such as the embroidery foot and quilting foot. Use the screwdriver to remove the presser foot holder. Remove the presser foot. a • For details, refer - Brother International SE-270D | Users Manual - English - Page 47
flap removed, free-arm sewing is possible. Pull the sliding leg (at the bottom of the b machine) out toward you. 1 a Sliding leg • During free-arm sewing, be sure to pull out the sliding leg. Slide the part that you wish to sew onto the c arm, and then sew from the top. Sewing Cylindrical Pieces 41 - Brother International SE-270D | Users Manual - English - Page 48
42 - Brother International SE-270D | Users Manual - English - Page 49
2 SEWING BASICS The necessary preparations for sewing are described in this chapter. Sewing ...44 Adjusting the Thread Tension 52 Adjusting the Stitch Width and Length 54 Useful Functions...56 Useful Sewing Tips 59 - Brother International SE-270D | Users Manual - English - Page 50
sewing machine. For details on turning on the machine, refer to "Turning on the machine" (page 11). ↓ 2 Select the stitch.. Select the stitch appropriate for the area to be sewn. For details on selecting a stitch, refer to "Selecting stitching" (page 45). ↓ 3 Attach the presser foot. Attach - Brother International SE-270D | Users Manual - English - Page 51
appears in the screen. For details, refer to "Replacing the Presser Foot" (page 38). Check that the correct presser foot is attached before starting to sew. If the wrong presser foot is installed, turn off the sewing machine, attach the correct presser foot, and then select the desired stitch again - Brother International SE-270D | Users Manual - English - Page 52
sides of the fabric are aligned correctly. Turn on the sewing machine. a Press (Needle position button) once or b twice to raise the needle. Lower the presser foot lever. e 1 a Needle position button Place the fabric under the presser foot. c • If the seam allowance is positioned on the right - Brother International SE-270D | Users Manual - English - Page 53
/stop button) once. Turn off the sewing machine. a When connecting the foot controller, be sure to turn off the sewing machine in order to prevent the machine from accidentally being started. 1 a Start/stop button X The machine starts sewing. Insert the foot controller plug into its jack on b the - Brother International SE-270D | Users Manual - English - Page 54
Note (For U.S.A. only) z Foot controller: Model N5V This foot controller can be used on this machine model SE-270D. Turn on the sewing machine. c When the end of the stitching is reached, f completely release the foot controller. X The machine stops sewing with the needle lowered (in the fabric - Brother International SE-270D | Users Manual - English - Page 55
then lower the presser foot lever. 1 a Reverse/reinforcement stitch button 2 X While the reverse/reinforcement stitch button is held pressed, reverse stitches are sewn. After sewing back to the beginning of the d stitching, release the reverse/reinforcement stitch button. X The machine stops - Brother International SE-270D | Users Manual - English - Page 56
z The sewing machine can be set to automatically sew reverse or reinforcement stitches at the beginning and end of the stitching. For details, refer to "Automatically sewing reverse/reinforcement stitches" (page 56). Raise the presser foot lever, then remove the b fabric. 1 a Presser foot lever - Brother International SE-270D | Users Manual - English - Page 57
on the side of the machine to cut the threads. a Thread cutter When you wish to finish the stitching and the a sewing machine is stopped, press (Needle position button) once. 1 a Needle position button X The needle is raised. Raise the presser foot lever. b 1 a Presser foot lever Sewing 51 - Brother International SE-270D | Users Manual - English - Page 58
SEWING BASICS Adjusting the Thread Tension The tensions of the upper thread and of the bobbin thread ( of fabric c Upper thread d Bobbin thread e The bobbin thread is visible from the right side of the fabric. Turn the thread tension dial downward to a lower number to loosen the upper thread. - Brother International SE-270D | Users Manual - English - Page 59
of the actual a fabric to be used. Referring to the illustration below, turn the b thread tension dial on the left side of the 2 sewing machine. The larger the number is, the greater the upper thread tension. Tight Loose 1 a Thread tension dial Test it until the thread tension is suitable - Brother International SE-270D | Users Manual - English - Page 60
. Turn on the sewing machine. a X The LCD sewing speed controller. For details, refer to "Satin stitching" (page 97). z means the setting cannot be adjusted. CAUTION ● After adjusting the stitch width, slowly turn the balance wheel toward you and check that the needle does not touch the presser foot - Brother International SE-270D | Users Manual - English - Page 61
stitch length can be adjusted on the LCD. Turn on the sewing machine. a Memo z To reset the stitch length to its standard If the stitches are bunched together, increase the stitch length. Continuing to 2 sew with the stitches bunched together Select a stitch. b X A screen containing settings - Brother International SE-270D | Users Manual - English - Page 62
Functions useful in improving sewing efficiency are described below. Automatically sewing reverse/ reinforcement stitches Position the fabric under the presser foot, and d then press (Start/stop button) once. The sewing machine can be set to automatically sew reverse or reinforcement stitches - Brother International SE-270D | Users Manual - English - Page 63
the stitching. Be sure to press the reverse/reinforcement stitch button at the end of the stitching. Automatically cutting the thread The sewing machine can be set to automatically cut the threads at the end of the stitching. This is called "programmed thread-cutting". If programmed threadcutting - Brother International SE-270D | Users Manual - English - Page 64
reinforcement stitching has been selected, this operation is unnecessary. X After the reverse stitching or reinforcement stitching has been done, the sewing machine stops, and the thread is cut. X The LCD comes on. Select a stitch. b • For details on selecting a stitch, refer to "Selecting - Brother International SE-270D | Users Manual - English - Page 65
direction When the stitching reaches a corner, stop the a sewing machine. Leave the needle lowered (in the fabric). If the needle remained up when the machine stopped sewing, press (Needle position button) to lower the needle. Raise the presser foot lever, and then turn the b fabric. Turn the - Brother International SE-270D | Users Manual - English - Page 66
that is too thick a to feed under the foot, raise the presser foot lever. Press the black button (Presser foot holding b pin) on the left side of zigzag foot "J". Keep the button held in and lower the presser foot. 1 1 a Stabilizer material or paper Sewing stretch fabrics First, baste the pieces of - Brother International SE-270D | Users Manual - English - Page 67
or a marking on the needle plate. ■ Aligning the fabric with the presser foot Sew while keeping the right edge of the presser foot a fixed distance from the edge of the fabric. 2 1 2 a Seam b Presser foot ■ Aligning the fabric with a needle plate marking The markings on the needle plate show - Brother International SE-270D | Users Manual - English - Page 68
62 - Brother International SE-270D | Users Manual - English - Page 69
. Stitch Settings...64 Overcasting Stitches 69 Basic Stitching ...73 Blind Hem Stitching 75 Buttonhole Stitching 77 Zipper Insertion...84 Sewing Stretch Fabrics and Elastic Tape 89 Appliqué, Patchwork and Quilt Stitching 91 Reinforcement Stitching 98 Eyelet Stitching...102 Decorative Stitching - Brother International SE-270D | Users Manual - English - Page 70
can be used are listed for utility stitches in the following table. Utility stitches Twin Needle Walking Foot Presser Foot Stitch Name Pattern Application 1 J Basic stitching, sewing gathers or pintucks, etc. Stitch Width [mm (inch.)] Auto 0.0 (0) Manual 0.0-7.0 (0-1/4) Stitch Length [mm - Brother International SE-270D | Users Manual - English - Page 71
Presser Foot Twin Needle Walking Foot Stitch Name Pattern Application 17 Blind hem stitch 18 R Blind hem stitching on mediumweight fabrics R Blind hem stitching on stretch fabrics Stitch Width [mm (inch.)] Stitch Length [mm (inch.)] Auto Manual Auto Manual and sewing overcasting on - Brother International SE-270D | Users Manual - English - Page 72
Presser Foot Twin Needle Walking Foot Stitch Name Pattern Application 29 J Decorative stitching Stitch Width [mm (inch.)] Auto 4.0 (3/16) Manual 0.0-7.0 (0-1/4) Stitch Length [mm (inch.)] Auto Manual 64-3/16) Yes Reinforcement No 33 Lace sewing, decorative N hemming, heirloom stitching, - Brother International SE-270D | Users Manual - English - Page 73
) No Automatic reinforcement No M Button sewing 3.5 2.5-4.5 (1/8) (3/32-3/16) - - No Reinforcement No N Sewing eyelets, for example, on belts 7.0 (1/4) J Piecing straight stitching (with a seam allowance of 6.5 mm from the right edge of the presser foot) 5.5 (7/32) J Piecing straight - Brother International SE-270D | Users Manual - English - Page 74
UTILITY STITCHES Presser Foot Twin Needle Walking Foot Stitch Name Quilting stitch (for stippling) Side cutter Pattern Application 62 J Quilting background stitching (stippling) Stitch Width [mm (inch.)] Stitch Length [mm (inch.)] Auto Manual Auto Manual Reverse/ Reinforcement Stitching - Brother International SE-270D | Users Manual - English - Page 75
edge of the fabric c against the guide of the presser foot, and then lower the presser foot lever. • For details, refer to "Replacing the presser foot" (page 38). Select a stitch. b 1 a Guide Sew with the edge of the fabric against the d presser foot guide. 1 • For details, refer to "Selecting - Brother International SE-270D | Users Manual - English - Page 76
Manual 1.4 0.0-4.0 (1/16) (0-3/16) 1.4 0.3-4.0 (1/16) (1/64-3/16) 1.0 0.2-4.0 (1/16) (1/64-3/16) 1.0 0.2-4.0 (1/16) (1/64-3/16) Presser Foot foot "J". a J Sew along the edge of the fabric with the c needle dropping off the edge at the right. • For details, refer to "Replacing the presser foot" - Brother International SE-270D | Users Manual - English - Page 77
Auto Manual 0.0 0.0-2.5 (0) (0-3/32) Stitch Length [mm (inch.)] Auto Manual Presser Foot 2.5 0.2-5.0 (3/32) (1/64-3/16) 64 Sewing in the presser foot holder, and then slowly lower the presser foot lever. Remove the presser foot. a • For details, refer to "Replacing the presser foot" (page - Brother International SE-270D | Users Manual - English - Page 78
rear of the sewing machine. Position the fabric in the side cutter. h The cut in the fabric should be positioned over the guide plate of the side cutter. Select a stitch. f 1 a Guide plate • If the fabric is not positioned correctly, the fabric will not be cut. Lower the presser foot lever, and - Brother International SE-270D | Users Manual - English - Page 79
Stitch Name Pattern Application Stitch Width [mm (inch.)] Auto Manual Stitch Length [mm (inch.)] Auto Manual Presser Foot 6 Basting stitch Temporarily securing 0.0 0.0-7.0 (0) (0-1/4) - - 1 Straight stitch Basic stitching and sewing gathers or pintucks (left baseline/ reverse stitching - Brother International SE-270D | Users Manual - English - Page 80
changed (between 0 and 7.0 mm (1/4 inch)), the needle position will also change. By changing the stitch width and sewing with the right side of the presser foot aligned with the edge of the fabric, a seam allowance can be sewn with a fixed width. 1 0.0 2.0 5.5 7.0 3 4 5 6 2 a Stitch width - Brother International SE-270D | Users Manual - English - Page 81
Manual 0.0 (0) 3← - 3→ 0.0 (0) 3← - 3→ Stitch Length [mm (inch.)] Auto Manual 2.0 1.0-3.5 (1/16) (1/16-1/8) 2.0 1.0-3.5 (1/16) (1/16-1/8) Presser Foot R Sew the edge of the folded e hem against the guide of the presser foot, and then lower the presser foot lever. 1 a Wrong side of fabric b - Brother International SE-270D | Users Manual - English - Page 82
a Wrong side of fabric b Right side of fabric • For details, refer to "Adjusting the stitch width" (page 54). Sew with the fold of the hem against the g presser foot guide. Remove the basting stitching. h 1 2 a Wrong side of fabric b Right side of fabric 1 2 a Wrong side of fabric b Right side - Brother International SE-270D | Users Manual - English - Page 83
one-step buttonholes, one for sewing on buttons. Stitch Name Pattern Application 42 Horizontal buttonholes on thin and mediumweight fabrics Stitch Width [mm (inch.)] Auto Manual Stitch Length [mm (inch.)] Auto Manual Presser Foot 5.0 3.0-5.0 0.4 0.2-1.0 (3/16) (1/8-3/16) (1/64) (1/64-1/16 - Brother International SE-270D | Users Manual - English - Page 84
stitching The names of parts of buttonhole foot "A", which is used for sewing buttonholes, are indicated below. Use chalk to mark on the fabric the position a and length of the buttonhole. 1 2 5 3 4 A a Button guide plate b Presser foot scale c Pin d Marks on buttonhole foot e 5 mm (3/16 inch - Brother International SE-270D | Users Manual - English - Page 85
and a thickness of 10 mm (3/8 inch), the button guide plate should be set to 25 mm (1 inch) on the scale. 1 A 2 a Mark on fabric (front) b Red marks on buttonhole foot Pass the upper thread down through the hole in the presser foot. • When lowering the presser foot, do not push in the front of the - Brother International SE-270D | Users Manual - English - Page 86
end of the buttonhole, and then use the seam ripper to cut open the buttonhole. X Once sewing is completed, the machine automatically sews reinforcement stitches, then stops. Raise the presser foot lever, remove the fabric, h and then cut the thread. Raise the buttonhole lever to its original - Brother International SE-270D | Users Manual - English - Page 87
part of a buttonhole foot "A" shown in the illustration. • For details, refer to "Adjusting the stitch width" (page 54). Memo z Before sewing buttonholes, check the stitch length and width by sewing . Lower the presser foot lever and the f buttonhole lever, and then start sewing. When sewing is - Brother International SE-270D | Users Manual - English - Page 88
, do not set the sewing machine for programmed-thread cutting. Adjust the stitch width so that it is the same as e the distance between the holes in the button. Place the button in the position where it will f be sewn, and lower the presser foot lever. Raise the presser foot lever, and then slide - Brother International SE-270D | Users Manual - English - Page 89
speed will be slow). X The sewing machine automatically stops after sewing reinforcement stitches. • Do not press the thread cutter button. Pull the upper thread at the end of the 3 i stitching to the wrong side of the fabric, and then tie it with the bobbin thread. Use scissors to cut the - Brother International SE-270D | Users Manual - English - Page 90
Name Pattern Application Straight stitch (center 3 needle position) Attaching zippers Sewing concealed seams and pintucks Stitch Width [mm (inch.)] Auto Manual Stitch Length [mm (inch.)] Auto Manual Presser Foot - - 2.5 0.2-5.0 (3/32) (1/64-3/16) I There are many methods for inserting - Brother International SE-270D | Users Manual - English - Page 91
a Pin on the right side b Needle drop point • For details, refer to "Replacing the presser foot" (page 38). a Stitching b Right side of fabric c Basting stitching d End of zipper opening CAUTION ● When sewing, be sure that the needle does not touch the zipper, otherwise the needle may bend or break - Brother International SE-270D | Users Manual - English - Page 92
refer to "Basic stitching" (page 73). Using a basting stitch, continue sewing to the c edge of the fabric. 1 3 2 4 a Basting presser foot holder to the right pin g of zipper foot "I". If the stitching will be sewn on the right side, attach the presser foot holder to the left pin of the zipper foot - Brother International SE-270D | Users Manual - English - Page 93
stitch 3 . h When you are about 5 cm (2 inch) from the j end of the zipper, stop the sewing machine with the needle lowered (in the fabric), raise the presser foot lever. Open the zipper and continue sewing. k • For details, refer to "Selecting stitching" (page 45). CAUTION ● When using zipper - Brother International SE-270D | Users Manual - English - Page 94
not touch the zipper, otherwise the needle may bend or break. When you are about 5 cm (2 inch) from the o end of the zipper, stop the sewing machine with the needle lowered (in the fabric), and then raise the presser foot lever. Remove the basting stitching, open the zipper, p and then continue - Brother International SE-270D | Users Manual - English - Page 95
[mm (inch.)] Auto Manual 1.0 1.0-3.0 (1/16) (1/16-1/8) Stitch Length [mm (inch.)] Auto Manual Presser Foot 2.5 1.0-4.0 (3/32) (1/ Sew the fabric without stretching it. c 2 a Elastic tape b Pin Attach zigzag foot "J". b J • For details, refer to "Replacing the presser foot" (page 38). Sewing - Brother International SE-270D | Users Manual - English - Page 96
that it is the same length as the fabric. While pulling the fabric behind the presser foot with your left hand, pull the fabric at the pin nearest the front of the presser foot with your right hand. CAUTION ● When sewing, be sure that the needle does not touch any pins, otherwise the needle may - Brother International SE-270D | Users Manual - English - Page 97
and Quilt Stitching The stitches that can be used for sewing appliqués, patchwork and quilts are described below. Stitch Name Manual 3.5 0.0-7.0 (1/8) (0-1/4) 3.5 0.0-7.0 (1/8) (0-1/4) Stitch Length [mm (inch.)] Auto Manual 1.4 0.0-4.0 (1/16) (0-3/16) 1.4 0.0-4.0 (1/16) (0-3/16) Presser Foot - Brother International SE-270D | Users Manual - English - Page 98
é, making sure that the needle drops just outside of the appliqué. 1 a Basting stitching Attach zigzag foot "J". d J • For details, refer to "Replacing the presser foot" (page 38). When sewing around corners, stop the machine with the needle in the fabric just outside of the appliqué, raise the - Brother International SE-270D | Users Manual - English - Page 99
place it over the lower piece. Sew the two pieces of fabric together so the b pattern spans over both pieces. Piecing Sewing together two pieces of 45). • The piecing straight stitch shows a "P" on the LCD. Sew with the side of the presser foot aligned d with the edge of the fabric. ■ For a seam - Brother International SE-270D | Users Manual - English - Page 100
and sew using stitch 58 . 1 Quilting Sandwiching batting between the top and bottom layers of fabric is called "quilting". Quilts can easily be sewn using the optional walking foot and the optional quilting guide. a 7 mm (1/4 inch) Baste the fabric to be quilted. a Remove the presser foot holder - Brother International SE-270D | Users Manual - English - Page 101
3 Place one hand on each side of the presser f foot, and then evenly guide the fabric while sewing. † Presser foot holder Note z When sewing with the walking foot, sew at a speed between slow and medium. z When quilting, use a 90/14 home sewing machine needle. Adjust the stem of the quilter so - Brother International SE-270D | Users Manual - English - Page 102
in place with your right c hand, and then tighten the presser foot holder screw using the screwdriver in your left hand. 1 a Feed dog position switch (as seen from the rear of the machine) X The feed dogs are lowered. Turn on the sewing machine, and then select a e stitch. • For details, refer to - Brother International SE-270D | Users Manual - English - Page 103
refer to "Selecting stitching" (page 45). • For details, refer to "Replacing the presser foot" (page 38). Turn on the sewing machine, and then press c (Settings key) in the operation panel. While sewing, slide the sewing speed g controller to adjust the stitch width. Slide the controller to the - Brother International SE-270D | Users Manual - English - Page 104
Stitch Width [mm (inch.)] Auto Manual Triple stretch 4 stitch Reinforcing the seams guide plate on buttonhole foot "A" to the desired length. (The distance between the markings on the presser foot scale is 5 mm (3/16 inch).) 1 • For details, refer to "Selecting stitching" (page 45). Start sewing - Brother International SE-270D | Users Manual - English - Page 105
thread down through the hole in the presser foot. • When lowering the presser foot, do not push in the front of the presser foot, otherwise the bar tack will not be sewn with the correct size. X Once sewing is completed, the machine automatically sews reinforcement stitches, then stops. Raise the - Brother International SE-270D | Users Manual - English - Page 106
) in front of the area to be darned, and then lower the presser foot lever. 2 1 a Tear b 2 mm (1/16 inch) Pass the upper thread down through the hole in the presser foot. • When lowering the presser foot, do not push in the front of the presser foot, otherwise the darning will not be sewn with the - Brother International SE-270D | Users Manual - English - Page 107
Raise the presser foot lever, remove the fabric, g and then cut the threads. Raise the buttonhole lever to foot. 1 2 a Buttonhole lever b Bracket Gently hold the end of the upper thread in f your left hand, and then start sewing. X Once sewing is completed, the machine automatically sews - Brother International SE-270D | Users Manual - English - Page 108
stitch Sewing eyelets, for example, on belts Stitch Width [mm (inch.)] Auto Manual 7.0, 6.0 or 7.0 5.0 (1/4) (1/4, 15/64 or 3/16) Stitch Length [mm (inch.)] Auto Manual 7.0, 6.0 or 7.0 5.0 (1/4) (1/4, 15/64 or 3/16) Presser Foot N Attach monogramming foot "N". a Lower the needle - Brother International SE-270D | Users Manual - English - Page 109
Name Pattern Application 26 Fagoting stitch 27 Sewing two pieces of fabric together across an open seam Stitch Width [mm (inch.)] Auto Manual 5.0 0.0-7.0 (3/16) (0-1/4) Stitch Length [mm (inch.)] Auto Manual Presser Foot 2.5 1.0-4.0 (3/32) (1/16-3/16) 5.0 2.5-7.0 2.5 1.0-4.0 (3/16) (3/25 - Brother International SE-270D | Users Manual - English - Page 110
down the middle of the thin paper or water-soluble stabilizer, sewing is easier. 3 1 Stitch Width [mm (inch.)] Auto Manual Stitch Length [mm (inch.)] Auto Manual Presser Foot 6.0 1.5-7.0 1.6 1.0-4.0 (15/64) (1/16-1/4) (1/16) (1/16-3/16) N 5.0 1.5-7.0 1.6 1.0-4.0 (3/16) (1/16-1/4) (1/16) (1/16 - Brother International SE-270D | Users Manual - English - Page 111
blouses and to decorate the edges of projects. Attach monogramming foot "N". a Smocking The decorative stitch created by stitching or not to sew directly on the edge of the fabric. • Pull up the bobbin thread. For details, refer to "Pulling up the bobbin thread" (page 31). Sew parallel stitching - Brother International SE-270D | Users Manual - English - Page 112
blouses or cuffs made of thin fabrics. Fold the fabric along the bias. a Attach zigzag foot "J". b J Pull out the threads for the straight stitches. g • For details, refer to "Replacing the presser foot" (page 38). Select stitch 20 , and then increase the thread c tension. • For details, refer - Brother International SE-270D | Users Manual - English - Page 113
a J a Needle drop point Unfold the fabric, and then iron the tucks e down to one side. • For details, refer to "Replacing the presser foot" (page 38). Sew together the right sides of the two pieces b of fabric, and then open up the seam 3 allowances. 2 1 1 3 a Wrong side of fabric b 7 mm - Brother International SE-270D | Users Manual - English - Page 114
machine may be damaged. Manually pass the thread through the eye of the needle from the front to the back. For details, refer to "Thread the needle manually (without using the needle threader)" (page 28). Attach monogramming foot "N". b CAUTION ● When sewing to "Replacing the presser foot" (page 38 - Brother International SE-270D | Users Manual - English - Page 115
threads from the fabric. a Sew along the other edge of the frayed section f so that it looks like the previous stitching. Attach monogramming foot "N". b N 3 Press , and set the horizontal mirror g image key back to OFF. • For details, refer to "Replacing the presser foot" (page 38). Select - Brother International SE-270D | Users Manual - English - Page 116
by an unfrayed section of about 4 mm (3/16 inch). 1 a 4 mm (3/16 inch) Attach monogramming foot "N". b • For details, refer to "Replacing the presser foot" (page 38). Select stitch 36 . c • For details, refer to "Selecting stitching" (page 45). Sew along the center of the unfrayed section. d N 110 - Brother International SE-270D | Users Manual - English - Page 117
4 EMBROIDERY The steps for embroidering will be explained here. Embroidering neatly 112 Attaching the embroidery foot 115 Attaching the embroidery unit 118 Preparing the fabric 122 Attaching the embroidery frame 126 Selecting embroidery patterns 128 Embroidering ...134 Convenient Functions - Brother International SE-270D | Users Manual - English - Page 118
causing the needle to break. Note z For good quality embroidery designs be sure to use embroidery thread designed for embroidery machines. z Before starting to sew, be sure there is enough bobbin thread. If you continue embroidering when the bobbin thread is low, the thread may become tangled. Memo - Brother International SE-270D | Users Manual - English - Page 119
needle. When embroidering on thick fabrics such as denim, use a 90/14 home sewing machine needle. Memo z A 75/11 needle is already installed when the sewing machine is purchased. z When replacing the needle, refer to "Replacing the needle" (page 35). CAUTION ● Since ball point needles (gold colored - Brother International SE-270D | Users Manual - English - Page 120
step by step The basic steps for embroidery are as follows. 1 Presser foot attachment Attach the embroidery foot "Q". For details on attaching the embroidery foot, refer to "Attaching the embroidery foot" (on the next page) ↓ 2 Checking the needle Use a needle matched to the fabric. For - Brother International SE-270D | Users Manual - English - Page 121
. Attaching the embroidery foot Attach the embroidery foot when embroidering. Have the included embroidery foot "Q" and a screwdriver ready. 1 2 a Embroidery foot bar b Caught by the presser foot holder CAUTION ● Before replacing the presser foot, be sure to turn off the sewing machine, otherwise - Brother International SE-270D | Users Manual - English - Page 122
sewing, always turn the balance wheel toward you slowly, and check to be sure that the needle does not hit the presser foot. The needle could be broken or bent. 1 2 a Embroidery foot bar b Needle clamp screw Secure the embroidery foot with the presser g foot holder screw. Set the embroidery foot - Brother International SE-270D | Users Manual - English - Page 123
, refer to "Attaching the presser foot holder" (page 40). 1 X The needle is raised. Turn off the sewing machine. b 4 Raise the presser foot lever. c 1 a Presser foot lever X The presser foot is raised. Loosen the presser foot holder screw and d remove the embroidery foot "Q". Turn the screwdriver - Brother International SE-270D | Users Manual - English - Page 124
unit will be explained here. CAUTION ● Do not move the sewing machine with the embroidery unit in place. The embroidery unit may be dropped and cause injury. ● Do not bring your hands or anything else close when the embroidery carriage and embroidery frame are moving. It could cause injury. Get the - Brother International SE-270D | Users Manual - English - Page 125
it all the way back into the slot. 1 Slide the embroidery unit onto the sewing d machine arm. Push it in until it clicks and stops. 1 2 2 a Embroidery unit connector slot b Cover X The embroidery unit is attached. Turn on the sewing machine. e CAUTION ● Push the cover all the way back into the - Brother International SE-270D | Users Manual - English - Page 126
Utility stitches cannot be selected when the embroidery unit is attached. X The embroidery carriage moves into a position where it can be stored. Turn off the sewing machine. d CAUTION ● Always turn off the sewing machine before removing the embroidery unit. It could cause malfunctions if removed - Brother International SE-270D | Users Manual - English - Page 127
unit to the left. Memo z The embroidery unit can be stored with embroidery frame (medium) or (small) attached. 1 a Removal lever X The embroidery unit separates from the sewing machine. 4 Close the cover on the embroidery unit f connector slot on the sewing machine. After the cover is pulled out - Brother International SE-270D | Users Manual - English - Page 128
stitches easily contract. CAUTION ● Always use stabilizer material when sewing embroidery projects. The needle may break or bend if you embroider side) c Attached surface † When it cannot be ironed or placed in the hoop. For fabrics, such as towels, which cannot be ironed or for embroidering in - Brother International SE-270D | Users Manual - English - Page 129
stabilizer material attached and the embroidery frame (medium), (small) and (large) ready. ■ Embroidery set (medium) Patterns with embroidery frame that matches the size of the pattern being embroidered. If the wrong size embroidery frame is used, the embroidery frame may be hit by the presser foot - Brother International SE-270D | Users Manual - English - Page 130
in from the top of the f fabric again, lining up on the inner frame and on outer frame. ■ Using embroidery sheets If the embroidery sheet attached to the embroidery frame is used, the embroidery can be sewn in exactly the right position on the fabric. 3 12 54 a Outer frame b Inner frame c Fabric - Brother International SE-270D | Users Manual - English - Page 131
frame or thin pieces like ribbon are being embroidered, use stabilizer material as a base to stretch on the frame. We recommend stabilizer material for embroidery. 1 2 3 Place the inner frame with the fabric on the d outer frame and stretch the fabric. • For details, refer to page 123. Remove the - Brother International SE-270D | Users Manual - English - Page 132
Bobbin" (page 16). Firmly insert the embroidery frame guide into d the embroidery carriage frame holder from the top. Line up the embroidery frame guide tabs and the embroidery carriage frame holder slots and push in until it clicks and stops. 1 Raise the presser foot lever. b 1 a Presser foot - Brother International SE-270D | Users Manual - English - Page 133
frame Be sure that the sewing machine is stopped. a Raise the presser foot lever. b CAUTION ● Do not hit the needle with your finger or the embroidery frame. It could result in injury or the breaking of the needle. 1 a Presser foot lever Press the part of the embroidery frame holder c in the - Brother International SE-270D | Users Manual - English - Page 134
embroidery is selected. Copyright Information Embroidery pattern types The patterns stored in the sewing machine and embroidery cards changing the upper thread according to the instructions displayed on the LCD. • For details, refer to "Selecting embroidery patterns" (page 131). ■ Frame patterns - Brother International SE-270D | Users Manual - English - Page 135
touch this key and then, press to switch the display. The sewing settings such as the specified character string and color are confirmed. Returns density can be changed. NAME OF COLOR: Typical color name EMBROIDERY: Embroidery thread color number COUNTRY: Country thread color number When one - Brother International SE-270D | Users Manual - English - Page 136
. This is used when a specific color is not sewn or when restarting the sewing machine after power has been turned off in the middle of the operation. Memo z When "The pattern is too large for the embroidery frame." is displayed, no more characters can be input. z Characters from different groups - Brother International SE-270D | Users Manual - English - Page 137
, such as fruit and animals, stored in the machine's computer memory. Memo z Refer to "Embroidery Pattern Color Change Table" in the Quick reference guide for samples of completed patterns and the thread used. Press embroidery pattern. a X The pattern selection screen is displayed. 4 Select - Brother International SE-270D | Users Manual - English - Page 138
EMBROIDERY Selecting a frame pattern X If a stitch is selected, it can be embroidered. Ten shapes, such as squares and circles, can be combined with 12 stitch types. Memo z Refer to "Frame patterns" in the Quick reference guide for frame pattern shapes and stitches. Press the frame pattern. a - Brother International SE-270D | Users Manual - English - Page 139
purchased in foreign countries may not work with your machine. Turn off the sewing machine. a Insert the embroidery card in the embroidery b card slot on the right side of the sewing machine. Face the arrow on the embroidery card toward you, and insert it in the direction of the arrow. Selecting - Brother International SE-270D | Users Manual - English - Page 140
on the LCD. 3 1 2 4 5 a Embroidery foot "Q" (recommended presser foot) b Current color step/Number of colors in design c Current name of color d Current color part e Next color part • Typical color names, embroidery thread/ country thread color number, needle count , and time to sew (after is - Brother International SE-270D | Users Manual - English - Page 141
is cut. Remove the thread cassette. i 1 a Presser foot lever Press e (Start/stop button). 1 a Thread cassette eject lever 4 1 a Start/stop button After progressing 5-6 stitches, press (Start/ f stop button), and the sewing machine will stop. Set up embroidery thread for the next color, j and - Brother International SE-270D | Users Manual - English - Page 142
neatly. Stretch the base fabric on the embroidery e frame. Set up the thread for appliquéing. f Lower the presser foot lever, and press g (Start/stop button). X The position for the appliqué is stitched, and the sewing machine stops. Lower the presser foot lever, and press c (Start/stop button - Brother International SE-270D | Users Manual - English - Page 143
Lower the presser foot lever, and press i (Start/stop button). Follow the instructions on the LCD, and j change thread colors as you sew. 4 Embroidering 137 - Brother International SE-270D | Users Manual - English - Page 144
a note of the values in the lower left when you change the size and position, you can sew with the same size and layout even if you have to turn the power back on in the middle of your work. 90 degree rotation key Rotates the embroidery 90° each time. The direction of - Brother International SE-270D | Users Manual - English - Page 145
Switches the position for beginning stitching between center/lower left of the design. Trial key Moves the embroidery unit carriage, and checks the embroidery range. Storing characters The characters you entered can be stored in the sewing machine memory. Since the stored characters will not be - Brother International SE-270D | Users Manual - English - Page 146
. Note z Only characters (not designs) can be stored in the machine memory. z Characters saved from an embroidery card must have the embroidery card inserted in the machine in order to retrieve the memory saved from the embroidery card. X The pocket selection screen is displayed. Select the pocket - Brother International SE-270D | Users Manual - English - Page 147
If embroidery fails, changed using the thread tension dial on the left side of the sewing machine. Resewing When the wrong color upper thread has been sewn, it 2 a right side b wrong side ■ Upper thread is too tight The lower thread will be visible on the front of the fabric. In this instance - Brother International SE-270D | Users Manual - English - Page 148
a design When the upper thread or the bobbin thread runs out while sewing, the sewing machine stops. Move the needle back about ten stitches and resume sewing. Set up the upper or bobbin thread. a Press . b Stopping while embroidering If the embroidery is stopped before it is complete, check the - Brother International SE-270D | Users Manual - English - Page 149
ten stitches before the total number of stitches confirmed in b. • Always detach the embroidery unit when you move the sewing machine. Turn on the sewing machine and select the Restart the embroidery. f pattern. k 4 Press . g Press . h Press (Forward one color) to move to the i beginning - Brother International SE-270D | Users Manual - English - Page 150
144 - Brother International SE-270D | Users Manual - English - Page 151
5 APPENDIX The various maintenance and troubleshooting procedures are described in this chapter. Maintenance...146 Troubleshooting ...148 Index ...157 - Brother International SE-270D | Users Manual - English - Page 152
it once with a wet cloth, wipe it again with a dry cloth. CAUTION ● Unplug the power supply cord before cleaning the machine, otherwise injuries or an electric shock may occur. Sewing performance will suffer if dust collects in the shuttle; therefore, it should be cleaned periodically. Turn off the - Brother International SE-270D | Users Manual - English - Page 153
with the spring. otherwise the upper thread may become tangled, the needle may break or sewing performance may suffer. For a new shuttle (part code: XC3153-051), contact your nearest authorized service center. 1 ● Be sure that the shuttle is correctly installed, otherwise the needle may break - Brother International SE-270D | Users Manual - English - Page 154
requesting service. If the problem persists, contact your retailer or the nearest authorized service center. Symptom Probable Cause Remedy The machine is not turned on. Turn on the machine. The sewing machine does not operate. The start/stop button was not pressed. The presser foot lever - Brother International SE-270D | Users Manual - English - Page 155
5 presser foot is scratched, or has a your retailer or the nearest authorized - burr on it. service center. The shuttle is scratched, or has a burr on it. Replace the shuttle. Contact your retailer or the nearest authorized service center. - A bobbin designed specifically for this machine is - Brother International SE-270D | Users Manual - English - Page 156
presser foot holder. The thread tension is incorrect. Adjust the tension of the upper thread. A bobbin designed specifically for this machine is not used. Incorrect bobbins will not work properly. Only use a bobbin designed specifically for this machine stitch length or sew with stitch is too - Brother International SE-270D | Users Manual - English - Page 157
is made while sewing. The upper thread was not threaded correctly. The shuttle is scratched, or has a burr on it. Correct the upper threading. Replace the shuttle. Contact your retailer or the nearest authorized service center. page 21 - A bobbin designed specifically for this machine is not - Brother International SE-270D | Users Manual - English - Page 158
fabric does not hang off. The fabric is catching. It is pinched. Stop the sewing machine and set the fabric up correctly. The carriage was moved while the embroidery frame was being removed or attached during embroidery. If the carriage is moved during the process, the pattern may be messed up - Brother International SE-270D | Users Manual - English - Page 159
or thread cutter button was pressed while the presser foot was raised. Either the start/stop button or the reverse/reinforcement stitch button was pushed at a screen other than the sewing screen. The bobbin winder is winding the bobbin. The reverse/reinforcement stitch button, needle position - Brother International SE-270D | Users Manual - English - Page 160
combine more than 25 character patterns. Bobbin thread has run out. Little bobbin thread remains. You tried to select a pattern that cannot be used with this sewing machine. A pattern is being stored. The time for completion of the embroidery is being calculated. [Card] on the LCD was pressed when - Brother International SE-270D | Users Manual - English - Page 161
, because the thread is tangled The sewing machine continues to beep for four seconds. The machine automatically stops. Be sure to check for the cause of the error, and correct it before continuing to sew. Press or . c 5 Turn off the sewing machine, then turn it on d again. Troubleshooting 155 - Brother International SE-270D | Users Manual - English - Page 162
, it is set to beep each time an operation panel key is pressed. This setting can be changed so that the machine does not beep. Turn on the sewing machine. a X The LCD comes on. Press b panel. (Settings key) in the operation X The settings screen appears. Press c (Next page key). Press OFF - Brother International SE-270D | Users Manual - English - Page 163
steps 114 B embroidery bobbin thread Cover A embroidery card slot Cover C back key Cover E balance wheel Cover C, 46, 82 embroidery cards 133 embroidery character selection 130 bar tack stitch 98 embroidery fabric preparation 122 basic sewing 44 embroidery foot installation 115 - Brother International SE-270D | Users Manual - English - Page 164
for embroidering 112 presser foot Cover C presser foot holder installation 40 presser foot holder removal & installation 40 presser foot lever Cover D presser foot replacement 38 previous page key Cover E problem-solving 148 pulling up bobbin thread 31 Q quick reference guide Cover A quilt - Brother International SE-270D | Users Manual - English - Page 165
adjustment 52 141 , thread tension dial Cover B 53 threading bobbin 20 , threading needle 21 25 threading needle manually 28 tips 59 touch panel Cover E trial sewing 59 , triple stretch stitch 73 98 troubleshooting 148 turning machine on/off 11 , twin needle Cover A 29 two threads - Brother International SE-270D | Users Manual - English - Page 166
English 885-S13 XC8545-021 Printed in China
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
 |
 |
Easy Thread Cassette System
Operation Manual
CPS5XV[Y
GETTING READY
SEWING BASICS
UTILITY STITCHES
EMBROIDERY
APPENDIX