Brother International SE-270D Users Manual - English - Page 106

Darning

Page 106 highlights

UTILITY STITCHES Darning Fabric that has been torn can be darned. Darning is sewn as shown below. 1 1 a Reinforcement stitching Determine the desired length of the darning. a Set the button guide plate on buttonhole foot "A" to the desired length. (The distance between the markings on the presser foot scale is 5 mm (3/16 inch).) 1 Select stitch 52 or 53 . c 2 3 4 a Presser foot scale b Length of darning c 5 mm (3/16 inch) d 7 mm (1/4 inch) • A bar tack with a maximum length of about 28 mm (1-1/8 inch) can be sewn. Attach buttonhole foot "A". b • For details, refer to "Replacing the presser foot" (page 38). • For details, refer to "Selecting stitching" (page 45). Position the fabric so that the needle is 2 mm d (1/16 inch) in front of the area to be darned, and then lower the presser foot lever. 2 1 a Tear b 2 mm (1/16 inch) Pass the upper thread down through the hole in the presser foot. • When lowering the presser foot, do not push in the front of the presser foot, otherwise the darning will not be sewn with the correct size. 100

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166

100
UTILITY STITCHES
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Darning
Fabric that has been torn can be darned.
Darning is sewn as shown below.
a
Reinforcement stitching
a
Determine the desired length of the darning.
Set the button guide plate on buttonhole foot
"A" to the desired length. (The distance between
the markings on the presser foot scale is 5 mm
(3/16 inch).)
a
Presser foot scale
b
Length of darning
c
5 mm (3/16 inch)
d
7 mm (1/4 inch)
• A bar tack with a maximum length of about
28 mm (1-1/8 inch) can be sewn.
b
Attach buttonhole foot "A".
• For details, refer to "Replacing the presser
foot" (page 38).
c
Select stitch
52
or
53
.
• For details, refer to "Selecting stitching" (page
45).
d
Position the fabric so that the needle is 2 mm
(1/16 inch) in front of the area to be darned,
and then lower the presser foot lever.
a
Tear
b
2 mm (1/16 inch)
Pass the upper thread down through the hole in
the presser foot.
• When lowering the presser foot, do not push
in the front of the presser foot, otherwise the
darning will not be sewn with the correct
size.
1
1
1
2
4
3
2
1