Dell OptiPlex Gn Reference and Installation Guide (.pdf) - Page 102

Plug and, Play Card Name, DeviceID, Number, Total Count, Card Select Number, Error

Get Dell OptiPlex Gn PDF manuals and user guides View all Dell OptiPlex Gn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

Table B-2. Configuration Manager Messages (continued) Message Probable Cause Corrective Action WARNING: Could not configure Plug and Play Card Name. The card(s) mentioned are not fully configured due to resource conflicts. WARNING: Could not configure PCI device, ID=DeviceID. Failed to configure Number of Total Count Plug and Play ISA devices. Use your system's configuration utility to resolve conflicts. Press any key to continue. If you do not know the allowable resource values for your Plug and Play or PCI expansion card, use the following procedure to locate and resolve the resource conflict: 1. Remove all card configurations from the ICU. See "Removing a Card" in Chapter 3 for instructions. 2. Reboot your system. The ICU should automatically configure your Plug and Play or PCI expansion card. 3. Add the ISA expansion cards back into the ICU, resolving any resource conflicts as they arise. See "Adding a Listed Card" in Chapter 3 for instructions. If your Plug and Play or PCI expansion card is not automatically configured when you reboot the system with all other cards removed, you should perform the following steps: 1. Contact the manufacturer of the card. 2. See the chapter titled "Getting Help" in your Diagnostics and Troubleshooting Guide or the section titled "Contacting Dell" in your online System User's Guide for instructions on obtaining assistance. WARNING: Boot Device conflict detected! CSN=Card Select Number Error=Error. One of the devices is attempting to use one or more resources assigned to the system's boot device. Perform the following procedure: 1. Start the ICU. 2. Identify the card marked config err. This card is attempting to use one or more resources required by the system's boot device. 3. Follow the procedure for the preceding error message in this table. NOTE: For the full name of an abbreviation or acronym used in this table, see the Glossary in the online System User's Guide. B-8 Dell OptiPlex Gn and Gn+ Low-Profile Systems Reference and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
B-8
Dell OptiPlex Gn and Gn+ Low-Profile Systems Reference and Installation Guide
WARNING: Could not
configure
Plug and
Play Card Name
.
WARNING: Could not
configure PCI device,
ID=
DeviceID
.
Failed to configure
Number
of
Total Count
Plug and Play ISA
devices. Use your sys-
tem’s configuration
utility to resolve
conflicts. Press any
key to continue.
The card(s) mentioned are
not fully configured due to
resource conflicts.
If you do not know the allowable resource
values for your Plug and Play or PCI expansion
card, use the following procedure to locate and
resolve the resource conflict:
1.
Remove all card configurations from the
ICU.
See “Removing a Card” in Chapter 3 for
instructions.
2.
Reboot your system.
The ICU should automatically configure
your Plug and Play or PCI expansion card.
3.
Add the ISA expansion cards back into
the ICU, resolving any resource conflicts
as they arise.
See “Adding a Listed Card” in Chapter 3
for instructions.
If your Plug and Play or PCI expansion card is
not automatically configured when you reboot
the system with all other cards removed, you
should perform the following steps:
1.
Contact the manufacturer of the card.
2.
See the chapter titled “Getting Help” in
your
Diagnostics and Troubleshooting
Guide
or the section titled “Contacting
Dell” in your online
System User’s Guide
for instructions on obtaining assistance.
WARNING: Boot Device
conflict detected!
CSN=
Card Select Number
Error=
Error
.
One of the devices is
attempting to use one or
more resources assigned to
the system’s boot device.
Perform the following procedure:
1.
Start the ICU.
2.
Identify the card marked
config err
.
This card is attempting to use one or more
resources required by the system’s boot
device.
3.
Follow the procedure for the preceding
error message in this table.
Table B-2.
Configuration Manager Messages
(continued)
Message
Probable Cause
Corrective Action
NOTE: For the full name of an abbreviation or acronym used in this table, see the Glossary in the online
System User’s Guide
.