Epson 2070 Service Manual - Page 132

Repairing C166 Psb/pse Board Assembly

Get Epson 2070 - LQ B/W Dot-matrix Printer PDF manuals and user guides
UPC - 010343812277
View all Epson 2070 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 132 highlights

Troubleshooting LQ-2070 Service Manual 5.4 REPAIRING C166 PSB/PSE BOARD ASSEMBLY This section provides instructions to repair a defective power supply board assembly. It describes various symptoms, likely causes, and checkpoints. Checkpoints refer to proper waveforms, resistances, and other values to check when evaluating the operation of any potentially faulty component. Check these values and take the appropriate action. Note: This information is necessary only for servicers who repair to the component level. Servicers who repair to the unit level (including all servicers in the U.S.) can ignore this section. WARNING The OPERATE switch on the control panel only turns the secondary power circuit on or off, so the primary circuit is live as long as the printer is connected to an AC power outlet. Before, you repair or touch the power supply board, be sure to disconnect the AC power outlet. Table 5-6. Repairing the C166 PSB/PSE Board Assembly Problem The 35 V and 5 V lines are not output when the printer is powered on. ^ Cause The diode bridge DB1 is dead. Checkpoint Measure the DC voltage between the pins 3 and 4 of the DB1. Solution Replace the DB1. The transformer coil is Measure the resistance of T1 transformer Replace open. coils at pins 12-15, 9-11, 7-8, 3-4. the T1. 5-10 Rev. A

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
5.4 REPAIRING C166 PSB/PSE BOARD ASSEMBLY
This section provides instructions to repair a defective power supply board assembly. It describes various
symptoms, likely causes, and checkpoints. Checkpoints refer to proper waveforms, resistances, and other
values to check when evaluating the operation of any potentially faulty component.
Check these values
and take the appropriate action.
Note:
This information is necessary only for servicers who repair to the component level.
Servicers who repair to
the unit level (including all servicers in the U.S.)
can ignore this section.
The
OPERATE
switch on the control panel only turns the secondary power circuit on or off, so
the primary circuit is live as long as the printer is connected to an AC power outlet. Before, you
repair or touch the power supply board, be sure to disconnect the AC power outlet.
Table 5-6. Repairing the C166 PSB/PSE Board Assembly
Problem
Cause
Checkpoint
Solution
The 35 V and
5 V lines are
not output
when the
printer is
powered on.
The diode bridge DB1
is dead.
Measure the DC voltage between the pins
3 and 4 of the DB1.
Replace
the DB1.
^
The transformer coil is
open.
Measure the resistance of T1 transformer
coils at pins 12-15, 9-11, 7-8, 3-4.
Replace
the T1.
Troubleshooting
LQ-2070 Service Manual
5-10
Rev. A