HP F4280 User Guide - Page 172

Paper messages, Solution, Cause, Resume

Page 172 highlights

Troubleshooting Chapter 12 • The software that came with the product was not installed correctly. • The software that came with the product is installed, but it was not running. No scan options Solution: Make sure the software is installed and running. For more information, see the Setup Guide that came with the HP All-in-One. Cause: The software that came with the product was not running, or has never been installed. Out of disk space Solution: Close some applications and try the task again. Cause: There was not enough available memory on your computer to perform the task. Paper messages The following is a list of paper-related error messages: • Cannot load paper from input tray • Ink is drying • Out of paper • Paper jam or misfeed • Paper mismatch • Wrong paper width Cannot load paper from input tray Solution: If the product is out of paper or there are only a few sheets remaining, load more paper in the input tray. If there is paper in the input tray, remove the paper, gently tap the stack of paper against a flat surface, and reload the paper into the input tray. To continue your print job, press the Resume button on the control panel of the product. Cause: There was not enough paper in the input tray. Ink is drying Solution: Leave the sheet in the output tray until the message disappears. If it is necessary to remove the printed sheet before the message disappears, carefully hold the printed sheet on the underside or the edges, and place it on a flat surface to dry. Cause: Transparencies and some other media require a drying time that is longer than normal. 170 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220

The software that came with the product was not installed correctly.
The software that came with the product is installed, but it was not running.
No scan options
Solution:
Make sure the software is installed and running. For more information,
see the Setup Guide that came with the HP All-in-One.
Cause:
The software that came with the product was not running, or has never been
installed.
Out of disk space
Solution:
Close some applications and try the task again.
Cause:
There was not enough available memory on your computer to perform the
task.
Paper messages
The following is a list of paper-related error messages:
Cannot load paper from input tray
Ink is drying
Out of paper
Paper jam or misfeed
Paper mismatch
Wrong paper width
Cannot load paper from input tray
Solution:
If the product is out of paper or there are only a few sheets remaining,
load more paper in the input tray. If there is paper in the input tray, remove the paper,
gently tap the stack of paper against a flat surface, and reload the paper into the input
tray. To continue your print job, press the
Resume
button on the control panel of the
product.
Cause:
There was not enough paper in the input tray.
Ink is drying
Solution:
Leave the sheet in the output tray until the message disappears. If it is
necessary to remove the printed sheet before the message disappears, carefully hold
the printed sheet on the underside or the edges, and place it on a flat surface to dry.
Cause:
Transparencies and some other media require a drying time that is longer
than normal.
Chapter 12
170
Troubleshooting
Troubleshooting