HP Pavilion xt500 HP Pavilion ze5100 Series and HP Omnibook xe4400 Series Note - Page 144

Command, Function Conexant, Voice Commands, AT* Commands

Get HP Pavilion xt500 - Notebook PC PDF manuals and user guides View all HP Pavilion xt500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 144 highlights

Reference Information Modem Reference Information Command +FMI +FMM +FMR +FPR=n +FRH=n +FRM=n +FRS=n +FTH=n +FTM=n +FTS=n Voice Commands +FCLASS=8 +VDR=a,b +VDT=a,b +VDX=a +VGM=n +VGR=n +VGS=n +VGT=n +VIP +VIT=n +VLS=n +VNH=n +VPR=n +VRA=n +VRN=n +VRXn +VSD=a,b +VSM=a,b,c,d +VSP=a +VTD=n +VTR +VTS=string +VTX AT* Commands *B *D Function (Conexant) Report modem manufacturer. Report modem model. Report modem version, revision, or date. Set DTE/modem interface rate in bits/sec: 0=automatic detection (default). Receive data with HDLC framing. Receive data. Receive silence, n×10 ms. Transmit data with HDLC framing. Transmit data. Stop transmission and wait, n×10 ms. Select voice mode. Set report ring cadence and timing of RING event code: a=0 disables ring cadence reporting, a=1 enables. b sets report content: 0=DROF and DRON messages only. Set report control tone cadence: a=0 disables ring cadence reporting, a=1 enables. b=0 reports CPOF and CPON messages only. Select speakerphone half-duplex (a=0) or full duplex (a=1). Set microphone gain of speakerphone function (0 to 255). Set gain for received voice samples (0 to 255). Set speaker gain of speakerphone function (0 to 255). Set volume (120 to 135). Initialize all voice parameters to defaults. Set initial value for DTE/modem inactivity timer (0 to 255 seconds). Select sources/destinations for analog data. Set automatic hangups: 0=enable, 1=disable, 2=disable automatic hangups in non-voice modes. Set DTE/modem interface rate (0=autobaud). Set delay between ringbacks before modem assumes remote station is off hook (0 to 255 x 0.1 sec). Set delay between ringbacks before modem assumes remote station is off hook (0 to 60 sec). Start voice reception: 0=start without periodic tone production, 1=start with periodic tone production. Set silence detection sensitivity and required period of silence before modem reports silence at end of voice receive. Set voice and silence compression methods, and voice sampling rate. Disable (a=0) or enable (a=1) speakerphone. Set beep duration (1 to 500 x 0.01 sec). Start voice transmission and reception. Send voice tones. Start voice transmission. Display black-listed numbers. Display delayed numbers. 144 Reference Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
Reference Information
Modem Reference Information
144
Reference Guide
Command
Function (Conexant)
+FMI
Report modem manufacturer.
+FMM
Report modem model.
+FMR
Report modem version, revision, or date.
+FPR=
n
Set DTE/modem interface rate in bits/sec: 0=automatic detection (default).
+FRH=
n
Receive data with HDLC framing.
+FRM=
n
Receive data.
+FRS=
n
Receive silence,
n
×10 ms.
+FTH=
n
Transmit data with HDLC framing.
+FTM=
n
Transmit data.
+FTS=
n
Stop transmission and wait,
n
×10 ms.
Voice Commands
+FCLASS=8
Select voice mode.
+VDR=
a
,
b
Set report ring cadence and timing of RING event code:
a
=0 disables ring cadence reporting,
a
=1 enables.
b
sets report content: 0=DROF and DRON messages only.
+VDT=
a
,
b
Set report control tone cadence:
a
=0 disables ring cadence reporting,
a
=1 enables.
b
=0 reports CPOF and CPON messages only.
+VDX=
a
Select speakerphone half-duplex (
a
=0) or full duplex (
a
=1).
+VGM=
n
Set microphone gain of speakerphone function (0 to 255).
+VGR=
n
Set gain for received voice samples (0 to 255).
+VGS=
n
Set speaker gain of speakerphone function (0 to 255).
+VGT=
n
Set volume (120 to 135).
+VIP
Initialize all voice parameters to defaults.
+VIT=
n
Set initial value for DTE/modem inactivity timer (0 to 255 seconds).
+VLS=
n
Select sources/destinations for analog data.
+VNH=
n
Set automatic hangups: 0=enable, 1=disable, 2=disable automatic hangups in non-voice modes.
+VPR=
n
Set DTE/modem interface rate (0=autobaud).
+VRA=
n
Set delay between ringbacks before modem assumes remote station is off hook (0 to 255 x 0.1 sec).
+VRN=
n
Set delay between ringbacks before modem assumes remote station is off hook (0 to 60 sec).
+VRX
n
Start voice reception: 0=start without periodic tone production, 1=start with periodic tone production.
+VSD=
a
,
b
Set silence detection sensitivity and required period of silence before modem reports silence at end of
voice receive.
+VSM=
a
,
b
,
c
,
d
Set voice and silence compression methods, and voice sampling rate.
+VSP=
a
Disable (
a
=0) or enable (
a
=1) speakerphone.
+VTD=
n
Set beep duration (1 to 500 x 0.01 sec).
+VTR
Start voice transmission and reception.
+VTS=
string
Send voice tones.
+VTX
Start voice transmission.
AT* Commands
*B
Display black-listed numbers.
*D
Display delayed numbers.