Home » Kyocera Manuals » Laser Printers » Kyocera 1010N » Manual Viewer

Kyocera 1010N Operation Guide - Page 153

Testing the Expansion Memory, printer and turn on the power.

UPC - 632983001004

Add to My Manuals
Save this manual to your list of manuals

Page 153 highlights

Expansion Memory Installation 7 Close the clips on the DIMM slot to secure the DIMM. 8 When you have finished installing the DIMM, replace the side cover and fasten it with the screw. To remove a DIMM: Remove the side cover as shown in steps 1 to 3 on page B-4, then carefully pull the end clips outwards and pull the DIMM out of the socket. Testing the Expansion Memory After you have finished installing DIMM in the printer, test the printer to see if installation succeeded. To test the expansion memory, proceed as follows: 1 Make sure the power switch is off. Plug the power cord into the printer and turn on the power. 2 When the printer is online, press and hold the or more. key for 3 seconds 3 If the installation succeeded, the amount of memory shown on the status page will correspond with the amount of expansion memory. (The factory installed memory size is 16 MB.) B-6

Section	Page
PP10 Operation Guide (FS-1010)	1
Contents	5
Introduction	9
Guide to the Manuals	10
Guide to the Operation Guide	11
Chapter 1 Basic Settings and Operations	12
1.1 Operator Panel	13
1.1.1 Indicators	14
1.1.2 Keys	14
1.2 KM-NET Remote Operation Panel Utility	18
1.2.1 Requirements	18
1.2.2 Installing the Remote Operation Panel	19
1.3 Configuring the Printer	23
1.3.1 Basic Settings for the Remote Operation Panel	23
1.3.2 Connecting the Remote Operation Panel Utility to the Printer	26
1.3.3 Menu Items	27
1.4 Paper	28
1.4.1 Number of Copies to be Printed	28
1.4.2 Page Orientation	29
1.4.3 Paper Source	30
1.4.4 Paper Size	31
1.4.5 Media Type Settings for Paper Sources	33
1.4.6 Paper Source Properties	35
1.4.7 Setting the Weight of the Custom Paper Type	36
1.5 Printer Environment	38
1.5.1 Setting the Print Density of the Custom Paper Type	38
1.5.2 KIR	40
1.5.3 EcoPrint	41
1.5.4 Resolution	42
1.5.5 Form Feed Timeout	43
1.5.6 Sleep Mode	44
1.5.7 Sleep Time	45
1.5.8 Emulation	46
1.5.9 Serial Interface Parameters	48
1.5.10 Network Interface Card Properties	50
1.5.11 RAM Disk	51
1.5.12 Checking Toner Container Remain	53
1.5.13 Remote Operation Panel Display Language	54
1.6 Other Settings	56
1.6.1 Printer Properties	56
1.6.2 Password for the Printer	57
1.6.3 Printer Memory Status	59
1.6.4 Host Buffer	60
1.6.5 Adding an Asset Number to the Printer	62
1.6.6 Displaying the Resource List	63
1.6.7 Sending PRESCRIBE Commands to the Printer	64
Chapter 2 Using the Printer Software	66
2.1 Installing the Printer Driver	67
2.1.1 Using Perallel/Serial Interfaces	67
2.1.2 Using USB Interface	74
2.2 Setting Up the Default Properties	81
2.2.1 Using the Option Paper Feeder	81
2.2.2 Selecting the Page Description Language	82
2.3 Printing from Windows Applications	84
2.3.1 Basic Printing Task	84
2.3.2 Setting Custom Paper Size	86
2.3.3 Advanced Media Settings	88
2.3.4 Printing Multiple Pages per Sheet	94
2.3.5 Changing the Size of the Document	96
2.3.6 Printing on Both Sides of Paper (Manual Duplex)	97
2.3.7 Changing the Resolution	101
2.3.8 Adjusting Grayscale	103
2.3.9 TrueType Fonts	104
Chapter 3 Maintenance	106
3.1 Toner Container Replacement	107
3.1.1 Toner Container Replacement Interval	107
3.1.2 Replenishing Toner	108
3.2 Cleaning	111
3.2.1 Printer Interior	111
Chapter 4 Troubleshooting	114
4.1 General Guide	115
4.2 Print Quality Problems	116
4.3 Indicators	118
4.3.1 Maintenance Messages	119
4.3.2 Errors Requiring Service Personnel Attention	121
4.3.3 Error Messages	124
4.3.4 Normal Indicator Display	126
4.4 Correcting a Paper Jam	127
4.4.1 Jam at the Face-down and Face-up Trays	127
4.4.2 Jam at the Paper Cassette	128
4.4.3 Jam Inside the Printer	128
Chapter 5 Paper Selection	130
5.1 General Guidelines	131
5.1.1 Paper Availability	131
5.1.2 Paper Specifications	131
5.2 Selecting the Right Paper	132
5.3 Special Paper	136
5.3.1 Transparency (overhead projection film)	136
5.3.2 Adhesive-Backed Labels	137
5.4 Paper Type	140
Appendix A Fonts	141
A.1 Internal Fonts	142
A.2 List of Fonts	143
A.2.1 Internal Scalable and Bitmap Fonts and KPDL Fonts	143
Appendix B Options	148
B.1 Available Options	149
B.2 Expansion Memory Installation	150
B.3 Memory (CompactFlash) Card	155
B.4 Network Interface Card	157
Appendix C Host Computer Interface	158
C.1 Parallel Interface	159
C.1.1 Parallel Interface Communication Modes	159
C.1.2 Interface Signals	159
C.2 USB Interface	163
C.2.1 Specifications	163
C.2.2 Interface Signals	163
C.3 Serial Interface (Option)	164
C.3.1 RS-232C Interface	164
C.3.2 RS-422A Interface	165
C.4 RS-232C/RS-422A Protocol	167
C.4.1 PRESCRIBE FRPO D0 Command	168
C.5 RS-232C Cable Connection	169
C.5.1 Obtain a Suitable RS-232C Cable	169
C.5.2 Connecting the Printer to the Computer	169
Appendix D Printer Specifications	172
Printer Specifications	173
Appendix E Glossary	175