Kyocera Ai5555 NC-2 Instruction Hand Book - Page 102

NC-2 Print Server Hardware Address, listed on the Status sheet as Ethernet

Get Kyocera Ai5555 PDF manuals and user guides View all Kyocera Ai5555 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

UNIX Printing Through TCP/IP Windows NT Instructions Assigning IP Address with ntBOOTP This procedure uses the BOOTP protocol. The NC-2 Print Server must be on the same network segment as the workstation that you are using to configure it, and the TCP/IP stack must be installed and operating. You may provide the IP address and other IP parameters to the printer's NC-2 Print Server on 32-Bit TCP/IP Stack (Windows NT & Windows 95) using the ntBOOTP.exe program. You will have to store the file in the Windows directory. You can use ntBOOTP Lite to configure the IP address instead of ARP. 1. Reset the print server. NOTE: The BOOTP request is for a finite period of time. The print server must be freshly reset for this to work. 2. From Windows Program Manager under File, select Run ntBOOTP.exe. 3. Pull down the Admin menu to Configure option. 4. Enter the IP address that you want to assign to the NC-2 Print Server; its Subnet Mask (make sure it matches what you are using on your subnet); Default Gateway (your router's IP address); and the MAC address of the NC-2 Print Server (Hardware Address, listed on the Status sheet as Ethernet Address). Use colons as delimiters as shown on the status sheet rather than the dashes Windows uses. 5. Click on Go. 6. Wait about five minutes. The NC-2 Print Server should recycle and produce a status sheet showing the IP parameters you have just entered. 7. Pull down Admin menu to Verify. You should get a message back stating that the Unit is Active. If you do not get this message, check that TCP/IP is enabled on the status sheet 8. When you get a response that your unit is active, you should be able to ping the NC-2 Print Server. 5-12 UNIX Printing Through TCP/IP

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
5-12 UNIX Printing Through TCP/IP
UNIX Printing Through TCP/IP
Windows NT Instructions
Assigning IP Address with ntBOOTP
This procedure uses the BOOTP protocol. The NC-2 Print Server must be
on the same network segment as the workstation that you are using to
configure it, and the TCP/IP stack must be installed and operating.
You may
provide the IP address and other IP parameters to the printer's
NC-2 Print Server on 32-Bit TCP/IP Stack (Windows NT & Windows 95)
using the
ntBOOTP.exe
program. You will have to store the file in the
Windows directory. You can use ntBOOTP Lite to configure the IP address
instead of ARP.
1. Reset the print server.
NOTE: The BOOTP request is for a finite period of time. The print server must be freshly
reset for this to work.
2. From Windows Program Manager under
File
, select
Run ntBOOTP.exe
.
3. Pull down the Admin menu to Configure option.
4. Enter the
IP address
that you want to assign to the NC-2 Print Server;
its
Subnet Mask
(make sure it matches what you are using on your subnet);
Default Gateway
(your router's IP address); and the
MAC address
of the
NC-2 Print Server (Hardware Address, listed on the Status sheet as Ethernet
Address). Use colons as delimiters as shown on the status sheet rather than
the dashes Windows uses.
5. Click on
Go
.
6. Wait about five minutes. The NC-2 Print Server should recycle and
produce a status sheet showing the IP parameters you have just entered.
7. Pull down Admin menu to Verify. You should get a message back stating
that the Unit is Active. If you do not get this message, check that TCP/IP is
enabled on the status sheet
8. When you get a response that your unit is active, you should be able to
ping the NC-2 Print Server.