Kyocera Ai5555 NC-2 Instruction Hand Book - Page 160

Media Selection Jumper - JP4

Get Kyocera Ai5555 PDF manuals and user guides View all Kyocera Ai5555 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 160 highlights

Jumper Settings Changing Jumper Settings Media Selection Jumper - JP4 The Media Selection jumper is changed only in rare circumstances when you want to make a Thinnet (10Base2) Ethernet connector, or when your 10BaseT hub does not support link integrity (10BaseT only). If you change this jumper to MAN (manual) for a Thinnet connection, you also need to change the Ethernet Interface Type Jumper. 1. To make the change, locate jumper JP4 on the board (see illustration below). 2. Remove the jumper from the AUT (automatic) setting and place it on the MAN (manual) setting, as shown. NC-2 Board Illustration JP10 o-o o NORM FACT MAN AUTO 10BT THIN o-o o o o-o JP4 JP3 JP5 o o-o RXA TXA BNC Connector A-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
A-7
Jumper Settings
Changing Jumper Settings
Media Selection Jumper - JP4
The Media Selection jumper is changed only in rare circumstances when
you want to make a Thinnet (10Base2) Ethernet connector, or when your
10BaseT hub does not support link integrity (10BaseT only).
If you change this jumper to MAN (manual) for a Thinnet connection, you
also need to change the Ethernet Interface Type Jumper.
1. To make the change, locate jumper JP4 on the board (see illustration
below).
2. Remove the jumper from the AUT (automatic) setting and place it on the
MAN (manual) setting, as shown.
BNC
Connector
RXA
JP5
JP3
JP4
MAN AUTO
10BT THIN
NC-2 Board Illustration
JP10
NORM FACT
o-o
o
o
o-o
o-o
o
o
o-o
TXA