Kyocera Ai5555 NC-2 Instruction Hand Book - Page 44

Parallel Port Settings - strobe

Get Kyocera Ai5555 PDF manuals and user guides View all Kyocera Ai5555 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

NetWare Configuration Using the Network Management Utility Using Help Screens Port This section describes all the settings that are required to configure the printing port on the print server; send test print jobs to the print server printer; and configure the print server status page. Parallel Port Settings The parallel ports is configured for strobe size only. Strobe size is the value for a hardware signal that is sent to a printer. This value depends on the strobe value the printer will accept and the length of cable between the print server and printer. This value may need to be changed if you have problems printing (the default value is 1.0). If you have problems, you should first change the value to a higher setting. Consult your printer manual for details. Test Printer The Test Printer menu lets you send a printer test to the print server port. If you want to send a printer test, then choose the type of print job you want to send to the printer - PostScript or ASCII. Once you select the print job type, click on [Start Test] to send the test print job. If you have not done so already, you will need to enter a password before performing this function. The factory default password is "sysadm." Enter the password in lowercase. Configure Status Page The Status Page menu lets you select whether you want to send a status page to the printer each time you power on the print server. • When the check box for [Print Status Page on Startup] is marked, a status page will be sent to the printer each time you power on the print server. • When the check box is empty, a status page is not sent at power up. • You also need to select the type of print job you want sent to the printer - a PostScript or ASCII print job. Click on the appropriate radio button. If you want to send a status page to the printer immediately, then click on [Generate Now]. Click on [Accept Settings] when you are finished making your entries. This puts your new entries into effect. Click on [Clear Inputs] to clear the entries you made or to revert to the previous settings. NetWare Configuration 3-23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
NetWare Configuration 3-23
NetWare Configuration
Using the Network Management Utility
Using Help Screens
Port
This section describes all the settings that are required to configure the
printing port on the print server; send test print jobs to the print server
printer; and configure the print server status page.
Parallel Port Settings
The parallel ports is configured for strobe size only. Strobe size is the value
for a hardware signal that is sent to a printer. This value depends on the
strobe value the printer will accept and the length of cable between the print
server and printer. This value may need to be changed if you have problems
printing (the default value is 1.0). If you have problems, you should first
change the value to a higher setting. Consult your printer manual for details.
Test Printer
The Test Printer menu lets you send a printer test to the print server port. If
you want to send a printer test, then choose the type of print job you want to
send to the printer - PostScript or ASCII. Once you select the print job type,
click on [Start Test] to send the test print job. If you have not done so
already, you will need to enter a password before performing this function.
The factory default password is "sysadm." Enter the password in lowercase.
Configure Status Page
The Status Page menu lets you select whether you want to send a status
page to the printer each time you power on the print server.
• When the check box for [Print Status Page on Startup] is marked, a status page will be sent to
the printer each time you power on the print server.
• When the check box is empty, a status page is not sent at power up.
• You also need to select the type of print job you want sent to the printer - a PostScript or
ASCII print job. Click on the appropriate radio button. If you want to send a status page to the
printer immediately, then click on [Generate Now].
Click on [Accept Settings] when you are finished making your entries. This
puts your new entries into effect. Click on [Clear Inputs] to clear the entries
you made or to revert to the previous settings.