Kyocera Ai5555 NC-2 Instruction Hand Book - Page 161

Ethernet Interface Jumper - JP3

Get Kyocera Ai5555 PDF manuals and user guides View all Kyocera Ai5555 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 161 highlights

Jumper Settings Changing Jumper Settings Ethernet Interface Jumper - JP3 Change this jumper when using Thinnet Ethernet connections. 1. Locate the JP3 Jumper on the board (see illustration below). 2. Remove the jumper from the 10BT setting and place it on the THIN setting, as shown. This jumper must be changed in connection with the Media Selection Type jumper described on the previous page. NOTE: After changing the jumper to the Thinnet connection, refer to the Installation instructions in Section 2, Connect the Network to NC-2: Ethernet. NC-2 Board Illustration JP10 o-o o NORM FACT MoANoAU-ToO o10BT oTH-IoN JP4 JP3 JP5 o o-o RXA TXA BNC Connector A-8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
A-8
Jumper Settings
Changing Jumper Settings
Ethernet Interface Jumper - JP3
Change this jumper when using Thinnet Ethernet connections.
1. Locate the JP3 Jumper on the board (see illustration below).
2. Remove the jumper from the 10BT setting and place it on the THIN
setting, as shown. This jumper must be changed in connection with the
Media Selection Type jumper described on the previous page.
NOTE: After changing the jumper to the Thinnet connection, refer to the Installation
instructions in Section 2,
Connect the Network to NC-2: Etherne
t.
BNC
Connector
RXA
JP5
JP3
JP4
MAN AUTO
10BT THIN
NC-2 Board Illustration
JP10
NORM FACT
TXA
o
o-o
o
o-o
o-o
o
o
o-o